Cisco WRP500 Administration Manual Download Page 110

Page: 110 / 128

R E V I E W D R A F T # 1 — C I S C O C O N F I D E N T I A L

B-20

Cisco WRP500 Administration Guide

Appendix B Data Fields

Applications and Gaming

Applications and Gaming > Port Range Forwarding

To IP Address

The IP address of the PC that should receive the
requests.

Enabled

When selected, port forwarding is active.

Application Name

A name for the application. Each name can be up to 12
characters.

Start~End Port

The number or range of port(s) used by the server or
Internet applications. Check with the Internet
application documentation for more information.

Protocol

The protocol used for this application, either TCP,
UDP, or both.

To IP Address

The IP address of the PC running the specific
application.

Enabled

When selected, port forwarding is active.

Summary of Contents for WRP500

































































































































Search results

Summary of Contents for WRP500

Reviews:

Related manuals for WRP500

Brands by name

Popular brands

Cisco WRP500, Administration Manual

Search results

Summary of Contents for WRP500

Reviews:

Related manuals for WRP500

Brands by name

Popular brands