Cisco WLC 5700 Series Command Reference Manual Download Page 80 | Manualshive

Page: 80 / 82

background image

udld reset

To reset all interfaces disabled by UniDirectional Link Detection (UDLD) and permit traffic to begin passing
through them again (though other features, such as spanning tree, Port Aggregation Protocol (PAgP), and
Dynamic Trunking Protocol (DTP) still have their normal effects, if enabled), use the

udld reset

command

in privileged EXEC mode.

udld reset

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Privileged EXEC

Command History

Modification

Release

This command was introduced.

Cisco IOS XE 3.2SE

Usage Guidelines

If the interface configuration is still enabled for UDLD, these ports begin to run UDLD again and are disabled
for the same reason if the problem has not been corrected.

Examples

This example shows how to reset all interfaces disabled by UDLD:

Controller#

udld reset

1 ports shutdown by UDLD were reset.

Related Commands

Description

Command

Displays UDLD administrative and operational status for all ports or the specified
port.

Enables aggressive or normal mode in UDLD or sets the configurable message
timer time.

Enables UDLD on an individual interface or prevents a fiber-optic interface from
being enabled by the

udld

global configuration command.

Layer 2/3 Command Reference, Cisco IOS XE Release 3E (Cisco WLC 5700 Series)

72

OL-32323-01

Layer 2/3 Commands

udld reset

«
...
78
79
80
81
82
»

Summary of Contents for WLC 5700 Series



















































































Reviews:

No comments

Related manuals for WLC 5700 Series

i-bus KNX IPR/S 3.5.1

Brand: ABB Pages: 44

Brand: Keithley Pages: 59

Brand: LaCie Pages: 44

LaCie Ethernet Disk

Brand: LaCie Pages: 2

5big - Network NAS Server

Brand: LaCie Pages: 9

Brand: LaCie Pages: 14

12big Rack Fibre 8

Brand: LaCie Pages: 9

Brand: Teac Pages: 20

cMT-FHDX Series

Brand: Maple Systems Pages: 2

Brand: NETGEAR Pages: 2

ION 1200 Series

Brand: PaloAlto Networks Pages: 90

RS-232/422/485 Serial Card CE 3PXCC4A

Brand: B&B Electronics Pages: 47

Brand: Gigabyte Pages: 18

Brand: Compro Technology Pages: 2

Brand: Korenix Pages: 25

Brand: JAKA Pages: 37

Brand: Socket Pages: 28

VAR-SOM-MX8M-PLUS

Brand: Variscite Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands