Cisco WLC 5700 Series Command Reference Manual Download Page 52 | Manualshive

Page: 52 / 82

background image

show etherchannel

To display EtherChannel information for a channel, use the

show etherchannel

command in user EXEC

mode.

show etherchannel

[

channel-group-number

| {

detail | port | port-channel | protocol | summary

}] | [

detail|

load-balance | port| port-channel| protocol| summary

]

Syntax Description

(Optional) Channel group number. The range is 1 to 128.

channel-group-number

(Optional) Displays detailed EtherChannel information.

detail

(Optional) Displays the load-balance or frame-distribution
scheme among ports in the port channel.

load-balance

(Optional) Displays EtherChannel port information.

port

(Optional) Displays port-channel information.

port-channel

(Optional) Displays the protocol that is being used in the
channel.

protocol

(Optional) Displays a one-line summary per channel group.

summary

Command Default

None

Command Modes

User EXEC

Command History

Modification

Release

This command was introduced.

Cisco IOS XE 3.2SE

Usage Guidelines

If you do not specify a channel group number, all channel groups are displayed.

In the output, the passive port list field is displayed only for Layer 3 port channels. This field means that the
physical port, which is still not up, is configured to be in the channel group (and indirectly is in the only port
channel in the channel group).

Examples

This is an example of output from the

show etherchannel channel-group-number detail

command:

Controller>

show etherchannel 1 detail

Group state = L2
Ports: 2

Maxports = 16

Layer 2/3 Command Reference, Cisco IOS XE Release 3E (Cisco WLC 5700 Series)

44

OL-32323-01

Layer 2/3 Commands

show etherchannel

«
...
50
51
52
53
54
...
»

Summary of Contents for WLC 5700 Series



















































































Reviews:

No comments

Related manuals for WLC 5700 Series

DES-3526 - Switch - Stackable

Brand: D-Link Pages: 258

Brand: H3C Pages: 33

S5500-SI Series

Brand: H3C Pages: 1217

Brand: 3Com Pages: 2443

Brand: H3C Pages: 3

Brand: H3C Pages: 4

S5120V3-EI Series

Brand: H3C Pages: 54

Brand: H3C Pages: 116

Brand: Idis Pages: 86

Brand: Paradyne Pages: 20

Brand: Paradyne Pages: 2

LightSpeed Appliance QLS250

Brand: Quantum Pages: 12

ZyXEL EES-1024AF

Brand: ZyXEL Communications Pages: 99

DM/IP601-CPCI-100BT

Brand: Dialogic Pages: 2

Brand: QUNDIS Pages: 42

Brand: Manson Engineering Industrial Pages: 10

Brand: PairGain Pages: 48

Brand: Atlantis Land Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands