Cisco Webex DX70 Administrator'S Manual Download Page 46

Page: 46 / 219

D15362.16 DX70 and DX80 Administrator Guide CE9.13, JUNE 2020.

Cisco Webex DX70 and DX80

Administrator Guide

Power On and Off

(page 1 of 2)

Power On/Off with the Power button

The power button, with LED indicator, is placed on the front as shown in the illustration.

Switch on

The device does not start automatically.

Press the power button gently, and hold for

a few seconds.

The LED is lit while the device starts up.

Switch off

Press the power button gently and hold until

the light goes out.

Enter/exit standby mode

Press the power button briefly. It takes a few

seconds before the device enters standby.

Power button with LEDs

encircling the button

Introduction

Configuration

Peripherals

Maintenance

Device settings

Appendices



Introduction

Summary of Contents for Webex DX70




























































































































































































































Search results

Summary of Contents for Webex DX70

Reviews:

Related manuals for Webex DX70

Brands by name

Popular brands

Cisco Webex DX70, Administrator'S Manual

Search results

Summary of Contents for Webex DX70

Reviews:

Related manuals for Webex DX70

Brands by name

Popular brands