Cisco UCS 6400 Series Hardware Installation Manual Download

Page: 65 / 68

Date

Time

Verified By

Planning Activity

Task No.

Cable and interface
equipment
evaluation:

• Cable type

• Connector type

• Cable distance

limitations

• Interface

equipment
(transceivers)

EMI evaluation:

• Distance

limitations for
signaling

• Site wiring

• RFI levels

Verify that the power supply installed in the chassis has a dedicated AC source circuit.

UPS = uninterruptible power supply.

EMI = electromagnetic interference.

RFI = radio frequency interference.

Contact and Site Information

Use the following worksheet to record contact and site information.

Table 16: Contact and Site Information

Contact person

Contact phone

Contact e-mail

Building/site name

Data center location

Floor location

Address (line 1)

Address (line 2)

Cisco UCS 6400 Series Fabric Interconnect Hardware Installation Guide

Site Planning and Maintenance Records

Contact and Site Information

Summary of Contents for UCS 6400 Series




































































Search results

Summary of Contents for UCS 6400 Series

Reviews:

Related manuals for UCS 6400 Series

Brands by name

Popular brands

Cisco UCS 6400 Series, Hardware Installation Manual

Search results

Summary of Contents for UCS 6400 Series

Reviews:

Related manuals for UCS 6400 Series

Brands by name

Popular brands