manualshive.com logo in svg

Cisco TelePresence DX70, Reference Manual

Share
Download
Cisco TelePresence DX70 Reference Manual Download Page 179

D15363.05 Cisco TelePresence DX70 and DX80 API Reference Guide CE9.2, NOVEMBER 2017. 

Copyright © 2017 Cisco Systems, Inc. All rights reserved. 

179

Cisco TelePresence DX70 and DX80

API Reference Guide

xStatus Security Persistency LocalPhonebook

Shows whether local phone book is set to persistent or non-persistent mode. Persistent is the 

default mode.

Requires user role: ADMIN, USER

Value space of the result returned: 

NonPersistent/Persistent

Example:

 

xStatus Security Persistency LocalPhonebook

*s Security Persistency LocalPhonebook: Persistent

** end

SIP status

xStatus SIP AlternateURI Alias [n] URI

Requires user role: ADMIN, USER

Value space of the result returned: 

String

Example:

 

xStatus SIP AlternateURI Alias

*s SIP AlternateURI Alias URI: ""

** end

xStatus SIP AlternateURI Primary [n] URI

Requires user role: ADMIN, USER

Value space of the result returned: 

String

Example:

 

xStatus SIP AlternateURI Primary

*s SIP AlternateURI Primary URI: ""

** end

xStatus SIP Authentication

Shows which authentication mechanism is used when registering to the SIP Proxy Server.
Digest: Uses the Digest access authentication method, as specified by RFC 2069.
NTLM: Uses the NTLM authentication method, which is a Microsoft authentication protocol.
Off: No authentication mechanism is used.

Requires user role: ADMIN, USER

Value space of the result returned: 

Digest/Off

Example:

 

xStatus SIP Authentication

*s SIP Authentication: Off

** end

Introduction

About the API

xConfiguration

Appendices

xCommand

xStatus

xStatus

Summary of Contents for TelePresence DX70











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands