Cisco StadiumVision SV-4K Deployment Manual Download

Page: 67 / 76

Monitoring Commands for the SV-4K Media
Player

Table 24. Management Dashboard Monitoring Commands

Command Name

Supported on SV-4K?

Get Status

Yes

Ping

Yes

Enable Monitoring

Change Monitoring Thresholds

Disable Monitoring

Switch Commands for the SV-4K Media Player

Table 25. Management Dashboard Switch Commands

Command Name

Supported on SV-4K?

Power Cycle DMP

Yes

Power On DMP

Yes

Power Off DMP

Yes

Run Cabling Test using TDR

Yes

Show TDR Test Results

Yes

Ping Test

Yes

Clear ARP Cache

Yes

TV Commands for the SV-4K Media Player

Table 26. Management Dashboard TV Commands

Command Name

Supported on SV-4K?

TV On

Yes

TV Off

Yes

Set Display Input

Yes

Set Display Banner

Yes

Set Closed Caption

Yes

Set Volume

Yes

Set Video Channel

Yes

Show Diagnostics

Yes

Supported beginning in Cisco StadiumVision Director Release 4.0.0-402.

59 of 68

Summary of Contents for StadiumVision SV-4K










































































Search results

Summary of Contents for StadiumVision SV-4K

Reviews:

Related manuals for StadiumVision SV-4K

Brands by name

Popular brands

Cisco StadiumVision SV-4K, Deployment Manual

Search results

Summary of Contents for StadiumVision SV-4K

Reviews:

Related manuals for StadiumVision SV-4K

Brands by name

Popular brands