Cisco SM-X-NIM-ADPTR Connecting Download Page 8

Page: 8 / 10

Connecting the Cisco Network Interface Module Adapter for SM-X Slot on the Cisco 4000 Seris Integrated Services

Connecting the Cisco Network Interface Module Adapter for SM-X Slot on Cisco 4300 and 4400 Series Integrated Services Routers

Verifying the SM-X-NIM-ADPTR Installation in a Cisco 4000 Series ISR

Use the

show diag

command to verify that the SM-X-NIM-ADPTR is correctly installed into the ISR as

shown in the following example:

Router#

show diag slot 2 eeprom

Slot 2 EEPROM data:

Product Identifier (PID) : SM-X-NIM-ADPTR

Version Identifier (VID) : V01

PCB Serial Number

: FOC18372FP5

Hardware Revision

: 1.0

CLEI Code

: IPU3BA6CAA

Router#

show diag slot 2 eeprom detail

Slot 2 EEPROM data:

EEPROM version

: 4

Compatible Type

: 0xFF

Controller Type

: 3205

Hardware Revision

: 1.0

PCB Part Number

: 73-16509-01

Top Assy. Part Number

: 800-42856-01

Board Revision

: 11

Deviation Number

: 0

Fab Version

: 01

PCB Serial Number

: FOC18372FP5

RMA Test History

: 00

RMA Number

: 0-0-0-0

RMA History

: 00

Product Identifier (PID) : SM-X-NIM-ADPTR

Version Identifier (VID) : V01

CLEI Code

: IPU3BA6CAA

Base MAC Address

: 50 87 89 C3 CF 15

MAC Address block size

: 2

Environment Monitor Data : 40 01 6D 43 00 01

Platform features

: 02 06 01 00 00 00 00 00

00 05 00

Fab Part Number

: 28-11899-01

Manufacturing Test Data : 00 00 00 00 00 00 00 00

Asset ID

Removing the SM-X-NIM-ADPTR from a Cisco 4000 Series ISR

Procedure

Step 1

Read the

“Safety Warnings” section on page 4

before you perform any module replacement.

Step 2

Locate the SM-X-NIM-ADPTR to be removed.

Step 3

Using a number 1 Phillips or flat-blade screwdriver, unscrew the captive mounting screws on the module
faceplate.

Summary of Contents for SM-X-NIM-ADPTR











Search results

Summary of Contents for SM-X-NIM-ADPTR

Reviews:

Related manuals for SM-X-NIM-ADPTR

Brands by name

Popular brands

Cisco SM-X-NIM-ADPTR, Connecting

Search results

Summary of Contents for SM-X-NIM-ADPTR

Reviews:

Related manuals for SM-X-NIM-ADPTR

Brands by name

Popular brands