Cisco TelePresence PrecisionHD Camera
D14640.12 Cisco Telepresence PrecisionHD Camera User Guide TC6.2, August 2013.
Copyright © 2010–2013 Cisco Systems, Inc. All rights reserved.
30
User Guide
The VISCA™/RS–232 control protocol, cont...
NOTE:
Some VISCA™ commands do not apply to the PrecisionHD 1080p2.5x/4x/4x S2 cameras.
Camera commands, continued...
*
Does not apply to PrecisionHD 1080p2.5x/4x/4x S2 cameras
Command
Command Packet
Comments
Mirror_On
8x 01 04 61 02 ff
Sony calls this CAM_LR_Reverse. RR
(FT/AT mirror command).
The “xConfiguration Cameras Camera
[1..n] Mirror: Auto” (supported by the
Codec C-series) do not apply to the
PrecisionHD 1080p 4x.
Mirror_Off
8x 01 04 61 03 ff
Flip_On
8x 01 04 66 02 ff
Sony calls this CAM_ImgFlip.
The “xConfiguration Cameras Camera
[1..n] Flip: Auto” (supported by the
Codec C-series) do not apply to the
PrecisionHD 1080p 4x.
Flip_Off
8x 01 04 66 03 ff
Gamma_Auto
8x 01 04 51 02 ff
Gamma mode. Default uses gamma
table 4.
Gamma_Manual
8x 01 04 51 03 ff
Gamma_Direct
8x 01 04 52 0p 0q 0r 0s ff
pqrs: Gamma table to use in manual
mode. Range 0-7.
MM_Detect_On
8x 01 50 30 01 ff
Turn on the Motor Moved Detection
(camera recalibrates if touched)
MM_Detect_Off
8x 01 50 30 00 ff
Turn off the Motor Moved Detection
(camera does not recalibrate if
touched)
Call_LED_On
8x 01 33 01 01 ff
Refers to orange LED on top of the
camera. It is always off at startup.
Call_LED_Off
8x 01 33 01 00 ff
Call_LED_Blink
8x 01 33 01 02 ff
Power_LED_On
8x 01 33 02 01 ff
Green power LED. If switched to off
and stored to startup profile, it is
always off.
Power_LED_Off
8x 01 33 02 00 ff
IR_Output_On
8x 01 06 08 02 ff
See IR push message.
IR_Output_Off
8x 01 06 08 03 ff
Command
Command Packet
Comments
IR_CameraControl_On
8x 01 06 09 02 ff
Lets the up/down/left/right/zoom+/-
on the IR remote control the camera
directly. Those keycodes are sent to
the controller if the IR Output is on.
IR_CameraControl_Off
8x 01 06 09 03 ff
Command
Command Packet
Comments
Zoom_Stop
8x 01 04 07 00 ff
Zoom_Tele
8x 01 04 07 2p ff
p = speed parameter,
a (low) to b (high)
Zoom_Wide
8x 01 04 07 3p ff
Zoom_Direct
8x 01 04 47 0p 0q 0r 0s ff
pqrs: zoom position
ZoomFocus_Direct
8x 01 04 47 0p 0q 0r
0s
0t 0u 0v 0w ff
pqrs: zoom position
tuvw: focus position
Focus_Stop
8x 01 04 08 00 ff
Focus_Far
8x 01 04 08 2p ff
p = speed parameter,
a (low) to b (high)
Focus_Near
8x 01 04 08 3p ff
Focus_Direct
8x 01 04 48 0p 0q 0r 0s ff
pqrs: focus position
PTZF - movement commands
Contents
Introduction
The Physical Interface
Connecting the Camera
Appendices
Daisy Chaining
Video Output Format
Appendices