Cisco PA-MC-2T3+ Installation And Configuration Manual Download Page 47

Page: 47 / 130

3-7

PA-MC-2T3+ Multi-Channel T3 Port Adapter Installation and Configuration

OL-3526-05

Chapter 3 Removing and Installing Port Adapters

Port Adapter Removal and Installation

Figure 3

Removing the Port Adapter Blank Panel

Step 1

Remove any port adapter blank panel that may be in place.

Move the lock lever on the top left corner of the Port Adapter Jacket Card until the port adapter blank
panel releases.

Pull the port adapter blank panel from the Port Adapter Jacket Card.

Figure 4

Installing a Port Adapter in the Port Adapter Jacket Card

Step 2

Insert the port adapter into the Port Adapter Jacket Card until it is fully seated.

Step 3

Move the port adapter lock lever to the locked position.

Port adapter lock lever

ETHERNET-10BFL

FAST SERIAL

LB CD

TOKEN RING

Cisco 7200

Series VXR

ETHERNET 10BT

ENABLED

LINK

ENABLED

MII

LINK

RJ45

FAST ETHERNET

138891

PORT ADAPTER JACKET CARD

Port adapter lock lever

ETHERNET-10BFL

FAST SERIAL

LB CD

TOKEN RING

Cisco 7200

Series VXR

ETHERNET 10BT

ENABLED

LINK

ENABLED

MII

LINK

RJ45

FAST ETHERNET

138885

PORT ADAPTER JACKET CARD

ENCRYPTION/COMPRESSION

SA-VAM2+

Summary of Contents for PA-MC-2T3+



































































































































Search results

Summary of Contents for PA-MC-2T3+

Reviews:

Related manuals for PA-MC-2T3+

Brands by name

Popular brands

Cisco PA-MC-2T3+, Installation And Configuration Manual

Search results

Summary of Contents for PA-MC-2T3+

Reviews:

Related manuals for PA-MC-2T3+

Brands by name

Popular brands