manualshive.com logo in svg

Cisco PA-2FEISL-FX, Installation And Configuration Manual

Share
Download
Cisco PA-2FEISL-FX Installation And Configuration Manual Download Page 53

4-9

PA-2FEISL 100BASE-T Fast Ethernet/ISL Port Adapter Installation and Configuration

OL-3475-02

Chapter 4      Configuring the PA-2FEISL

  Checking the Configuration

Using the show diag Command

Display the types of port adapters installed in your system (and specific information about each) using 
the 

show diag

 

slot

 command, where 

slot

 is the 

port adapter slot

 in a Cisco 7100 series,

Cisco 7200 series, and Cisco uBR7200 series router and the 

interface processor slot

 in a Cisco 7000 

series or Cisco 7500 series router with a VIP2.

Note

The ouputs that appear in this document may not match the output you receive when running these 
commands. The outputs in this document are examples only.

Cisco 7100 Series Routers

Use the 

show diag

slot

 command to determine which type of port adapter is installed in your system. 

Specific port adapter information is displayed, as shown in the following example of a PA-2FEISL-FX 
in port adapter slot 2:

Router# 

show diag 2

Fastethernet (TX-ISL) port adapter, 2 ports

        Port adapter is analyzed 

        Port adapter insertion time 00:02:27 ago

        Hardware revision 1.0           Board revision A0

        Serial number     8500290       Part number    73-2618-01

        Test history      0x0           RMA number     00-00-00

        EEPROM format version 1

        EEPROM contents (hex):

          0x20: 01 6C 01 00 00 81 B4 42 49 0A 3A 01 00 00 00 00

          0x30: 50 00 00 00 98 04 00 00 00 00 FF FF FF FF FF 00

Note

For complete command descriptions and examples for the Cisco 7100 series, Cisco 7200 series, and 
Cisco uBR7200 series routers, refer to the publications listed in the 

“Obtaining Documentation” section 

on page vii

.

Note

To use the 

show diag

 command with the Cisco 7140 series router, replace the slot argument 

3

 with

 

4

.

Cisco 7200 Series and Cisco uBR7200 Series Routers

Use the 

show diag

slot

 command to determine which type of port adapter is installed in your system. 

Specific port adapter information is displayed, as shown in the following example of a PA-2FEISL-FX 
in port adapter slot 2:

Router# 

show diag 2

Fastethernet (TX-ISL) port adapter, 2 ports

        Port adapter is analyzed 

        Port adapter insertion time 00:02:27 ago

        Hardware revision 1.0           Board revision A0

        Serial number     8500290       Part number    73-2618-01

        Test history      0x0           RMA number     00-00-00

        EEPROM format version 1

        EEPROM contents (hex):

          0x20: 01 6C 01 00 00 81 B4 42 49 0A 3A 01 00 00 00 00

          0x30: 50 00 00 00 98 04 00 00 00 00 FF FF FF FF FF 00

Summary of Contents for PA-2FEISL-FX



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands