Cisco ONS 15454 Hardware Installation Manual Download | Manualshive

Page: 49 / 516

background image

ONS 15454 M6

The ONS 15454 M6 shelf assemblies have eight card slots numbered sequentially from bottom to top. Slots
1 and 8 are reserved for control cards (TNC, TNCE, TSC, TNCS-2, TNCS-2O, or TSCE). Slots 2, 3, 4, 5, 6,
and 7 are dedicated for common line cards.

The ONS 15454 M6 system can work with a single control card (TNC, TNCE, TSC, TNCS-2, TNCS-2O, or
TSCE). The TNC, TNCE, TSC, TNCS-2, TNCS-2O, and TSCE cards cannot operate in a shelf at the same
time.

Caution

The shelf assembly slots have symbols indicating the type of cards that you can install in them. Each card has
a corresponding symbol. The symbol on the card must match the symbol on the slot.

Figure 6: Slot Symbols

The following table shows the slot and card symbol definitions.

Table 5: Slot and Card Symbols

Definition

Symbol Color/Shape

Slots 1 and 8. TNC/TNCE/TSC/TSCE/TNCS-2/TNCS-2O card slot. Install cards
only with a square symbol on the faceplate.

Purple/Square

Slots 2 to 7. Install cards only with a circle symbol on the faceplate.

Orange/Circle

Slots 2 to 7. New line cards with high-speed backplane connectors.

Orange/Hollow Circle

Slots 4 and 5. New Uplink card.

Pink/Pentagon

When the ONS 15454 M6 shelf is powered at –60 VDC (nominal), only TNC, OPT-AMP-C, OPT-AMP-17-C,
OPT-EDFA-17, OPT-EDFA-24, and 15454-M6-ECU-60 can be installed. For more information about ONS
15454 M6 DC power options, see the

DC Power Module, on page 353

.

Note

Card Replacement

To replace a card with another card of the same type, you do not need to make any changes to the database;
remove the old card and replace it with a new card. To replace a card with a card of a different type, physically
remove the card and replace it with the new card, then delete the original card from CTC. For specifics, refer
to the “Maintain the Node” chapter in the Cisco ONS 15454 DWDM Configuration Guide.

Cisco ONS 15454 Hardware Installation Guide

19

Preparing to Install the ONS 15454 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

ONS 15454 M6

«
...
47
48
49
50
51
...
»

Summary of Contents for ONS 15454





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ONS 15454

Brand: Quantum Pages: 32

Brand: Viglen Pages: 58

Teleline 750003

Brand: Positron Pages: 34

FlexPoint Powered Chassis 4385

Brand: Omnitron Systems Technology Pages: 4

NetPerformer SDM-9600

Brand: Memotec Pages: 94

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands