Cisco ONS 15454 Hardware Installation Manual Download Page 475

Page: 475 / 516

Figure 295: Replacing the Air Filter—AC Power Module

Step 4

Replace the air filter with a new one if the air filter is dirty or clogged with dust.

Step 5

Close the front door. If you removed the door, complete the

NTP-G258 Install the Standard Door of the ONS

15454 M6 Shelf , on page 323

Stop. You have completed this procedure.

NTP-G115 Clean Fiber Connectors

This procedure cleans the fiber connectors.

Purpose

Inspection microscope

Type A Fiber Optic Connector Cleaner (CLETOP reel)

Optical swab

Optical receiver cleaning stick

Tools/Equipment

None

Prerequisite Procedures

Required

Required/As Needed

Onsite

Onsite/Remote

Cisco ONS 15454 Hardware Installation Guide

445

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G115 Clean Fiber Connectors

Summary of Contents for ONS 15454




































































































































































































































































































































































































































































































































Search results

Summary of Contents for ONS 15454

Reviews:

Cisco ONS 15454, Hardware Installation Manual, Page: 475 / 516

Search results

Summary of Contents for ONS 15454

Reviews: