Cisco ONS 15454 Page 192 Hardware Installation Manual Download | Manualshive

Page: 192 / 516

background image

Figure 76: 40-Channel Patch-Panel Tray, Side View

The following figure shows the 40-channel patch-panel ports and corresponding wavelengths.

Figure 77: 40-Channel (15454-PP-80) Patch-Panel Port Wavelengths

Mesh Patch-Panel Tray

There are two mesh patch-panel trays, four-degree (PP-MESH-4) and eight-degree (PP-MESH-8), which are
intended for use with mesh nodes. Both trays are 2 RUs deep. The four-degree patch panel allows up to 4
sides to be used per mesh node, while the eight-degree patch panel allows up to 8 sides to be used per mesh
node. The 4-degree patch-panel tray can host up to 4 MPO-MPO and 4 LC-LC cables, and the 8-degree
patch-panel tray can host up to 8 MPO-MPO and 8 LC-LC cables. The module fits 19- and 23-inch (482.6-mm
and 584.2-mm) ANSI racks and 600 mm (23.6 inch) x 300 mm (11.8 inch) ETSI racks, using reversible
brackets.

The following figure shows a four-degree patch-panel tray.

Cisco ONS 15454 Hardware Installation Guide

162

Installing the ONS 15454 M12 (ANSI and ETSI) Shelf

Mesh Patch-Panel Tray

«
...
190
191
192
193
194
...
»

Summary of Contents for ONS 15454





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ONS 15454

Brand: Apevia Pages: 11

Brand: National Instruments Pages: 6

Case Storage CS350

Brand: SilverStone Pages: 32

NetPerformer SDM-9600

Brand: Memotec Pages: 94

Centellis 2000 Series

Brand: Artesyn Embedded Technology Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands