Cisco ONS 15454 Page 130 Hardware Installation Manual Download | Manualshive

Page: 130 / 516

background image

NTP-G10 Attach Wires to Alarm, Timing, LAN, and Craft Pin
Connections

This procedure installs alarm, timing, LAN, and craft wires on the ONS 15454
shelf. These wires are attached to the mechanical interface card (MIC) FMECs
on the ETSI shelf and are attached to the backplane on the ANSI shelf.

Purpose

Connectors according to function

Twisted #22 or #24 AWG (0.51 mm² or 0.64 mm²) shielded wires for LAN or
craft

75-ohm coaxial cable with 1.0/2.3 miniature coax connector

0.51 mm² or 0.64 mm² (#22 or #24 AWG) alarm wires

Tools/Equipment

NTP-G6 Install the MIC-A/P and MIC-T/C/P FMECs (ETSI Only), on page 66

NTP-G5 Remove the Backplane Covers (ANSI Only), on page 63

Prerequisite Procedures

As needed

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

Always use the supplied ESD wristband when working with a powered ONS 15454 ETSI. For detailed
instructions on how to wear the ESD wristband, refer to the

Electrostatic Discharge and Grounding Guide for

Cisco CPT and Cisco ONS Platforms

Caution

Procedure

Step 1

For an ONS 15454 ETSI shelf, complete the following tasks as necessary:

• Complete the

DLP-G20 Install Alarm Wires on the MIC-A/P (ETSI Only), on page 101

if you want to

provision external alarms and/or controls with the AIC-I card.

• Complete the

DLP-G21 Install Timing Wires on the MIC-C/T/P (ETSI Only), on page 104

if you are

provisioning external timing.

• Complete the

DLP-G22 Install LAN Wires on the MIC-C/T/P (ETSI Only), on page 105

to create an

external LAN connection. You must either install LAN wires on the MIC-C/T/P or connect a CAT-5
Ethernet cable to the LAN port on the TCC2/TCC2P/TCC3 card to create an external LAN connection.

Step 2

For an ONS 15454 ANSI shelf, complete the following tasks as necessary:

• Complete the

DLP-G23 Install Alarm Wires on the Backplane (ANSI Only), on page 106

if you are using

an AIC-I card and are not using an AEP.

Cisco ONS 15454 Hardware Installation Guide

100

Installing the ONS 15454 M12 (ANSI and ETSI) Shelf

NTP-G10 Attach Wires to Alarm, Timing, LAN, and Craft Pin Connections

«
...
128
129
130
131
132
...
»

Summary of Contents for ONS 15454





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ONS 15454

Brand: ERECA Pages: 19

EasyNote V Series

Brand: Packard Bell Pages: 27

Brand: National Instruments Pages: 6

Brand: Supermicro Pages: 52

Brand: National Instruments Pages: 7

Brand: Tektronix Pages: 214

ZDXModemRack EN61000-3-2

Brand: Multitech Pages: 2

Brand: LevelOne Pages: 10

Brand: Aurora Pages: 57

Brand: Wisi Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands