manualshive.com logo in svg

Cisco ONS 15454, Hardware Installation Manual, Page: 419 / 516

Share
Download
Cisco ONS 15454 Hardware Installation Manual Download Page 419

Error messages appear on the TNC, TNCE, TSC, or TSCE card, the fan-tray LED, and in the Cisco Transport
Controller (CTC) when the fan-tray assembly is removed from the shelf or when one fan is not working.

Note

To install the fan-tray assembly, it is not necessary to move any of the fiber-routing facilities.

Note

Procedure

Step 1

Insert the fan-tray assembly inside the left slot (fan tray slot) of the ONS 15454 M6 chassis (see the following
figure).

Figure 261: Installing the Fan-Tray Assembly

Step 2

Push the fan-tray assembly such that the backplane connector is engaged completely.

Step 3

Tighten the screws to a torque value of 4 in-lb (0.45 N-m) to lock the fan-tray assembly into the chassis (see
the following figure).

Cisco ONS 15454 Hardware Installation Guide

389

Installing the ONS 15454 M6 Shelf

NTP-G257 Install the Fan-Tray Assembly in the ONS 15454 M6 Shelf

Summary of Contents for ONS 15454





































































































































































































































































































































































































































































































































Reviews:

No comments