Cisco ONS 15454 Page 22 Hardware Installation Manual Download | Manualshive

Page: 22 / 516

background image

Notes

Date

• Revised the part number and included Release 9.8 features such as AC2 power module.

July 2013

• Added Release 10.0 feature on deep-front panel. Updated section “4.1 Front Door”.

• NTP-G343 Install the Air Plenum in ONS 15454 M2 Shelf.
• DLP-G763 Install Air Plenum for ONS 15454 M2 Shelf in ANSI 19-inch

Configuration.

• DLP-G764 Install Air Plenum in ONS 15454 M2 Shelf for ANSI 23-inch

Configuration.

• DLP-G765 Install Air Plenum for ONS 15454 M2 Shelf in ETSI Configuration.

• Added Release 10.0 feature on air plenum to orient the air flow within the chassis in

section “5.4 Air Plenum“.

• NTP-G344 Install the Air Plenum in ONS 15454 M6 Shelf
• DLP-G766 Install Air Plenum for ONS 15454 M6 Shelf in ANSI 19-inch Cabinet.
• DLP-G767 Install Air Plenum in ONS 15454 M6 Shelf for ANSI 23-inch

Configuration.

• DLP-G768 Install Pre-assembled Air Plenums in ANSI 23-inch Configuration.
• DLP-G769 Install Air Plenum for ONS 15454 M6 Shelf in ETSI Configuration.

November 2013

• The full length book-PDF was generated.

April 2014

• Added information for the 15454-M6-DC40 power module.

December 2014

• Added a note to the section, “Alarm Connectors” in the chapter “Installing the ONS

15454 M6 Shelf”.

June 2015

• Updated for R10.5.2

January 2016

Added the following note:

Due to memory limitations, TCC2/TCC2P cards are not supported as the node controller
in multi-shelf configuration from R10.5.2.6. Hence, it is recommended to use TCC3 card
as the node controller in multi-shelf configuration. However, the TCC2/TCC2P cards can
be used as a subtended controller and also in a stand-alone configuration.

April 2016

Updated the bandwidth specifications for ONS 15454 M6 in the appendix, “Hardware
Specifications”.

June 2016

Updated the sections, “Filler and Blank Cards” in the chapters, “Installing the ONS 15454
M12 (ANSI and ETSI) Shelf”, “Installing the ONS 15454 M2 Shelf”, and “Installing the
ONS 15454 M6 Shelf”.

July 2016

Included R 10.6.1 features.

November 2016

Added a note to "DLP-G298 Install LAN Wires in ONS 15454 M6" in the chapter,
"Installing the ONS 15454 M6 Shelf".

March 2017

Updated for R10.6.2

April 2017

Updated for R11.1

October 2019

Cisco ONS 15454 Hardware Installation Guide

xxii

Preface

Preface

«
...
20
21
22
23
24
...
»

Summary of Contents for ONS 15454





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ONS 15454

Brand: LG Pages: 16

SC825MTQ-R700LPB

Brand: Supermicro Pages: 78

Brand: Phanteks Pages: 35

Brand: ATX Pages: 90

Brand: Cisco Pages: 12

Nexus 9000 Series

Brand: Cisco Pages: 74

Brand: Cisco Pages: 22

Brand: Cisco Pages: 110

Brand: Cisco Pages: 175

Brand: Cisco Pages: 124

Nexus 9000 Series

Brand: Cisco Pages: 562

Brand: Cisco Pages: 114

Brand: Cisco Pages: 14

Brand: Cisco Pages: 50

Brand: Juniper Pages: 9

Brand: NI Pages: 22

Brand: Lets Go Aero Pages: 13

Brand: Multitech Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands