manualshive.com logo in svg

Cisco ONS 15454, Hardware Installation Manual, Page: 20 / 516

Share
Download
Cisco ONS 15454 Hardware Installation Manual Download Page 20

Notes

Date

• Updated the note in the section “Fan Tray Units for ONS 15454 Cards” in the chapter

“Installing the ONS 15454 (ANSI and ETSI) Shelf”.

• Updated the section “Fan-Tray Assembly” and the procedure “NTP-G268 Install the

Fan-Tray Assembly in the ONS 15454 M2 Shelf” in the chapter “Installing the ONS
15454 M2 Shelf”.

• Updated the section “Fan-Tray Assembly” and the procedure “NTP-G257 Install the

Fan-Tray Assembly in the ONS 15454 M6 Shelf” in the chapter “Installing the ONS
15454 M6 Shelf”.

• Updated the table “Fan-Tray Assembly Power Requirements” and the section “System

Power” in the appendix “Hardware Specifications”.

• Added the procedure “DLP-G729 Connect the ONS 15454 M6 as the Node Controller

in a Mixed Multishelf Configuration without a Catalyst Switch” in the chapter,
“Installing the ONS 15454 M6 Shelf”.

May 2012

• Updated the section “Multishelf Management” in the chapter “Installing the ONS

15454 M6 Shelf”.

• Updated the sections “NTP-G308 Connect the ONS 15454 M6 Multishelf Node and

the ONS 15454 M6 Subtending Shelves” and “NTP-G310 Upgrade the ONS 15454
Multishelf Configuration using the ONS 15454 M6” in the chapter “Installing the
ONS 15454 M6 Shelf”.

June 2012

• Added a section “Cooling Profile” in the chapter “Installing the ONS 15454 M6

Shelf”.

• Updated the section “Multishelf LAN Topologies” in the chapter “Installing the ONS

15454 M6 Shelf”.

July 2012

Updated the table “Multishelf LAN Topologies in Cisco ONS 15454 M6 and Cisco ONS
15454” in the chapter “Installing the ONS 15454 M6 Shelf”.

August 2012

Updated the table “Multishelf LAN Topologies in Cisco ONS 15454 M6 and Cisco ONS
15454” in the chapter “Installing the ONS 15454 M6 Shelf”.

October 2012

• Updated the section “Mounting Multiple Nodes” in the chapter “Installing the ONS

15454 M6 Shelf” and “Mounting a Single Node” in the chapter “Installing the ONS
15454 M2 Shelf”.

• In the chapter “Maintaining the ONS 15454 (ANSI and ETSI), ONS 15454 M2 and

ONS 15454 M6 Shelf”, updated the procedures:

• NTP-G114 Inspect and Replace the Air Filter
• NTP-G274 Replace the Air Filter of the ONS 15454 M2 Shelf Assembly
• NTP-G262 Replace the Air Filter of the ONS 15454 M6 Shelf Assembly
• NTP-G263 Replace the Air Filter of the AC Power Module in the ONS 15454

M6 Shelf Assembly

November 2012

Cisco ONS 15454 Hardware Installation Guide

xx

Preface

Preface

Summary of Contents for ONS 15454





































































































































































































































































































































































































































































































































Reviews:

No comments