Cisco ONS 15454 Page 186 Hardware Installation Manual Download | Manualshive

Page: 186 / 516

background image

Filler and Blank Cards

The filler card (15454- FILLER) is designed to occupy empty multiservice and AIC-I slots in the Cisco ONS
15454 (Slots 1 to 6, 9, and 12 to17). The filler card cannot operate in the cross-connect (XC) slots (Slots 8
and 10) or TCC2/TCC2P/TCC3 slots (Slots 7 and 11). The filler card is detected by CTC.

When installed, the filler card aids in maintaining proper air flow and EMI requirements.

Do not use 15454-M-FILLER or 15454-M-T-FILLER filler cards in the Cisco ONS 15454 M12 shelf.

Note

The following figure shows the card faceplate. The filler card has no card-level LED indicators.

Blank cards (15454-BLANK) can be installed in any empty slot in the shelf. CTC does not detect blank cards.

Cisco ONS 15454 Hardware Installation Guide

156

Installing the ONS 15454 M12 (ANSI and ETSI) Shelf

Filler and Blank Cards

«
...
184
185
186
187
188
...
»

Summary of Contents for ONS 15454





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ONS 15454

Brand: GearMo Pages: 6

Brand: Brocade Communications Systems Pages: 182

Brand: HP Pages: 104

Brand: National Instruments Pages: 9

mAGE424U40-PCI-E-EXP

Brand: iStarUSA Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands