manualshive.com logo in svg

Cisco ONS 15454 M6, Maintenance Manual

The Cisco ONS 15454 M6 is a cutting-edge network transport platform designed for seamless connectivity. Ensure a hassle-free installation with our comprehensive and easy-to-follow Installation Manual. Download the manual for free from our website manualshive.com and unlock the full potential of this incredible product.

Share
Download
background image

The air filters are single-use only. They must not be cleaned and reused. This is a Telcordia NEBS requirement,
GR-63-CORE Issue 4.

Note

Air filters must be inspected every month. If they are dirty or clogged with dust, they must be replaced with
a new air filter.

Note

Procedure

Step 1

Open the front door of the shelf assembly (see

NTP-G259 Open and Remove the Standard Door of the ONS

15454 M6 Shelf

). If the shelf assembly does not have a front door, continue with Step 3.

Step 2

(Optional) Complete the

DLP-G577 Remove the Standard Door of the ONS 15454 M6 Shelf

to remove the

front door. If you do not want to remove the door, proceed to Step 3.

Step 3

Push the retention feature present on the right side of the shelf assembly to the left side (see the following
figure).

Figure 6: Replacing the Air Filter

Step 4

Extract the air filter from the shelf assembly (see the following figure).

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

8

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G262 Replace the Air Filter of the ONS 15454 M6 Shelf Assembly

Summary of Contents for ONS 15454 M6

































Reviews:

No comments

Related manuals for ONS 15454 M6

Brands by name

Popular brands

Load more brands