Cisco ONS 15454 M6 Maintenance Manual Download | Manualshive

Page: 24 / 32

background image

NTP-G260 Replace the Fan-Tray Assembly of the ONS 15454 M6
Shelf Assembly

This procedure replaces the fan-tray assembly of the ONS 15454 M6 shelf
assembly.

Purpose

Small slot-head screwdriver

Tools/Equipment

NTP-G257 Install the Fan-Tray Assembly in the ONS 15454 M6 Shelf

Prerequisite Procedures

Required

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

Do not force a fan-tray assembly into place. Doing so can damage either the connectors on the fan tray or the
connectors on the back panel of the shelf assembly, or both.

Caution

The estimated time required to change a fan-tray assembly is 2 minutes.

Note

Procedure

Step 1

Open the front door of the shelf assembly (see

DLP-G576 Open the Standard Door of the ONS 15454 M6

). If the shelf assembly does not have a front door, continue with Step 3.

Step 2

(Optional) Complete the

DLP-G577 Remove the Standard Door of the ONS 15454 M6 Shelf

to remove the

front door. If you do not want to remove the door, proceed to Step 3.

Step 3

Untighten the screws on the fan-tray assembly (see the following figure).

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

24

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G260 Replace the Fan-Tray Assembly of the ONS 15454 M6 Shelf Assembly

«
...
22
23
24
25
26
...
»

Summary of Contents for ONS 15454 M6

































Reviews:

No comments

Related manuals for ONS 15454 M6

SCOPIA Elite 5230

Brand: RADVision Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands