Cisco ONS 15454 M6 Maintenance Manual Download | Manualshive

Page: 22 / 32

background image

NTP-G272 Replace the Fan-Tray Assembly of the ONS 15454 M2
Shelf Assembly

This procedure replaces the fan-tray assembly of the ONS 15454 M2 shelf
assembly.

Purpose

Small slot-head screwdriver

Tools/Equipment

NTP-G268 Install the Fan-Tray Assembly in the ONS 15454 M2 Shelf

Prerequisite Procedures

Required

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

Do not force a fan-tray assembly into place. Doing so can damage either the connectors on the fan tray or the
connectors on the back panel of the shelf assembly, or both.

Caution

The estimated time required to change a fan-tray assembly is 2 minutes.

Note

Procedure

Step 1

Loosen the screw on the fan-tray assembly (see the following figure).

Figure 14: Fan-Tray Assembly installed in the ONS 15454 M2 Shelf Assembly

Step 2

Extract the fan-tray assembly partially to disconnect the backplane connector and wait until the fan stops (see
the following figure)

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

22

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G272 Replace the Fan-Tray Assembly of the ONS 15454 M2 Shelf Assembly

«
...
20
21
22
23
24
...
»

Summary of Contents for ONS 15454 M6

































Reviews:

No comments

Related manuals for ONS 15454 M6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands