Cisco ONS 15454 M6 Maintenance Manual Download | Manualshive

Page: 16 / 32

background image

Figure 11: Shelf Assembly with Door Ground Strap Retrofit Kit Installed (ANSI)

Step 6

Swing the door closed and lock the door with the provided pinned-hex key. Turn the key clockwise to lock
the door; counterclockwise to unlock it.

Stop. You have completed this procedure.

NTP-G116 Replace the Fan-Tray Assembly of the ONS 15454
Shelf Assembly

This procedure replaces a malfunctioning fan-tray assembly.

Purpose

None

Tools/Equipment

NTP-G257 Install the Fan-Tray Assembly in the ONS 15454 M6 Shelf

Prerequisite Procedures

As needed

Required/As Needed

Onsite

Onsite/Remote

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

16

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G116 Replace the Fan-Tray Assembly of the ONS 15454 Shelf Assembly

«
...
14
15
16
17
18
...
»

Summary of Contents for ONS 15454 M6

































Reviews:

No comments

Related manuals for ONS 15454 M6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands