Cisco ONS 15454 M6 Installation Manual Download

Page: 9 / 164

Figure 6: Minimum rear opening for ANSI 19-inch and ETSI configuration

NTP-G344 Install the Air Plenum in ONS 15454 M6 Shelf

This procedure installs the air plenum to orient the air flow from front-to- back
direction in the ONS 15454 M6 shelf.

Purpose

• #2 Phillips Dynamometric screwdriver
• Medium slot-head screwdriver
• Small slot-head screwdriver
• Screws

• ANSI: #12-24 x 0.50 pan-head Phillips screws
• ETSI: M6.0 x 20 pan-head Phillips screws

• Wing head screws (8)
• Adapter plates
• One air plenum kit (horizontal and vertical air plenums)

Tools/Equipment

As needed

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

Before performing any of the following procedures, ensure that power is removed from the DC circuit.

Statement 1074

Warning

Before working on a chassis or working near power supplies, unplug the power cord on AC units.

Statement 246

Warning

Installing the ONS 15454 M6 Shelf

NTP-G344 Install the Air Plenum in ONS 15454 M6 Shelf

Summary of Contents for ONS 15454 M6





































































































































































Search results

Summary of Contents for ONS 15454 M6

Reviews:

Related manuals for ONS 15454 M6

Brands by name

Popular brands

Cisco ONS 15454 M6, Installation Manual

Search results

Summary of Contents for ONS 15454 M6

Reviews:

Related manuals for ONS 15454 M6

Brands by name

Popular brands