manualshive.com logo in svg

Cisco ONS 15454 M6, Installation Manual

The Cisco ONS 15454 M6 is a cutting-edge network transport platform designed for seamless connectivity. Ensure a hassle-free installation with our comprehensive and easy-to-follow Installation Manual. Download the manual for free from our website manualshive.com and unlock the full potential of this incredible product.

Share
Download
background image

DLP-G688 Upgrade the ONS 15454 Multishelf with MS-ISC Card Configuration

Use this task to upgrade the existing ONS 15454 multishelf configuration that
has the MS-ISC card installed, with the ONS 15454 M6 subtending shelves and
Cisco Catalyst 3950.

Purpose

• Two Cisco Catalyst 3560 switches must be installed in same rack as the node

controller shelf; refer to the Cisco Catalyst 3560 product documentation for
installation instructions.

• Cross-over (CAT-5) LAN cables (3, plus 2 for each subtending shelf)

Tools/Equipment

•

NTP-G15 Install the Common Control Cards

•

NTP-G313 Install and Configure the TNC, TNCE, TSC, or TSCE Card

Prerequisite Procedures

As needed

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

Use TCC3 cards in ONS 15454 node controller while connecting it to the ONS 15454 M6 subtending shelves
and when there are more than 12 subtending shelves.

Note

The CTC in ONS 15454 M6 shelf view displays the three ports of the MS-ISC card, and EMS and circuit
ports present on the ECU.

Note

Procedure

Step 1

Disconnect the ONS 15454 subtending shelf from the EAPs:

a) Remove the cross-over (CAT 5) LAN cable (connecting the ONS 15454 subtending shelf) from the SSC8

port of the right EAP.

b) Remove the cross-over (CAT 5) LAN cable (connecting the ONS 15454 subtending shelf) from the SSC8

port of the left EAP.

Step 2

Connect the EAPs to the Catalyst 3560:

a) Using a cross-over (CAT-5) LAN cable:

•

• Plug one connector to the SSC8 port of the right EAP.
• Plug the other connector to Port 1 of the active Catalyst 3560.

b) Using a cross-over (CAT-5) LAN cable:

•

• Plug one connector to the SSC8 port of the left EAP.
• Plug the other connector to Port 1 of the standby Catalyst 3560.

Installing the ONS 15454 M6 Shelf

153

Installing the ONS 15454 M6 Shelf

DLP-G688 Upgrade the ONS 15454 Multishelf with MS-ISC Card Configuration

Summary of Contents for ONS 15454 M6





































































































































































Reviews:

No comments

Related manuals for ONS 15454 M6

Brands by name

Popular brands

Load more brands