Cisco ONS 15454 M6 Installation Manual Download Page 143 | Manualshive

Page: 143 / 164

background image

In order to connect the ONS 15454 M6 subtending shelves to the ONS 15454 M6 node controller
without using a catalyst, follow the steps described in

NTP-G308 Connect the ONS 15454 M6

Multishelf Node and the ONS 15454 M6 Subtending Shelves, on page 137

. To connect an ONS

15454 subtending shelf to the ONS 15454 M6 node controller without using a catalyst switch,
connect the MSM ports that correspond to the TNC/TNCE/TSC/TSCE cards in Slot 1 and Slot 8
of the ONS 15454 M6 node controller to the ONS 15454 subtending shelf TCC2/TCC2P/TCC3
cards in Slot 7 and Slot 11.

Note

Step 7

Return to your originating procedure (NTP).

DLP-G729 Connect the ONS 15454 M6 as the Node Controller in a Mixed
Multishelf Configuration without a Catalyst Switch

Use this procedure to connect the ONS 15454 M6 as the node controller and a
mix of ONS 15454 and ONS 15454 M6 as subtending shelves without using a
Catalyst switch.

Purpose

• Cross-over (CAT-5) LAN cables (3, plus 2 for each subtending shelf)

Tools/Equipment

NTP-G15 Install the Common Control Cards

.

NTP-G313 Install and Configure the TNC, TNCE, TSC, or TSCE Card

Prerequisite Procedures

As needed

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

The MSM (multishelf management) ports are present on the ECU module. The MSM ports located on the left
side of the ECU module correspond to the TNC/TNCE/TSC/TSCE card in Slot 1, and the MSM ports located
on the right side correspond to the TNC/TNCE/TSC/TSCE card in Slot 8. For more information about the
ECU module and MSM ports, see the

External Connection Units, on page 72

.

Note

Use the craft terminal port or the EMS port present on the ECU module to connect the ONS 15454 M6 node
controller to the LAN.

Note

Procedure

Step 1

To connect an ONS 15454 M6 subtending shelf to the ONS 15454 M6 node controller, complete the following:

a) Using a cross-over (CAT-5) LAN cable:

•

• Plug one connector into the MSM port of the subtending ONS 15454 M6 shelf that corresponds

to the TNC/TNCE/TSC/TSCE card in Slot 1.

Installing the ONS 15454 M6 Shelf

143

Installing the ONS 15454 M6 Shelf

DLP-G729 Connect the ONS 15454 M6 as the Node Controller in a Mixed Multishelf Configuration without a Catalyst Switch

«
...
141
142
143
144
145
...
»

Summary of Contents for ONS 15454 M6





































































































































































Reviews:

No comments

Related manuals for ONS 15454 M6

Brand: TEUPEN Pages: 56

Brand: Festo Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands