Cisco Nexus C9316D-GX Hardware Installation Manual Download Page 43

Page: 43 / 52

Power Specifications

Power specifications include the specifications for each type of power supply module.

1100-W AC Power Supply Specifications

These specifications apply to the following power supplies:

• NXA-PAC-1100W-PE2

• NXA-PAC-1100W-PI2

Specification

Characteristic

Nominal range: 100 and 240 VAC (Range: 90-132
VAC, 180-264 VAC)

AC input voltage

Nominal range: 50 to 60 Hz (Range: 47-63 Hz)

AC input frequency

13 A at 100 VAC

6 A at 240 VAC

Maximum AC input current

1300 VA at 100 VAC

Maximum input volt-amperes

1100 W

Maximum output power per power supply

33 A (sub-cycle duration)

Maximum inrush current

12 ms at 1100 W

Maximum hold-up time

12 VDC

Power supply output voltage

12 VDC

Power supply standby voltage

Climate Savers Platinum Efficiency (80Plus Platinum
certified)

Efficiency rating

RSP1

Form factor

1100-W HVAC/HVDC Power Supply Specifications

These specifications apply to the following power supplies:

• NXA-PHV-1100W-PE

• NXA-PHV-1100W-PI

Specification

Characteristic

94%

Efficiency

100VAC – 277VAC, 240VDC – 380VDC

Input voltage

Cisco Nexus C9316D-GX ACI-Mode Switch Hardware Installation Guide

System Specifications

Power Specifications

Summary of Contents for Nexus C9316D-GX




















































Search results

Summary of Contents for Nexus C9316D-GX

Reviews:

Related manuals for Nexus C9316D-GX

Brands by name

Popular brands

Cisco Nexus C9316D-GX, Hardware Installation Manual

Search results

Summary of Contents for Nexus C9316D-GX

Reviews:

Related manuals for Nexus C9316D-GX

Brands by name

Popular brands