Cisco Nexus 9364C-GX Hardware Installation Manual Download Page 58

Page: 58 / 64

Photo

Cord Set Description

Part Number

HVDC

6.6-foot (2.0 m) cable with
Saf-D-Grid and three terminal
connectors

CAB-HVDC-3T-2M

Not applicable

All except Argentina, Brazil, and
Japan

No power cord included with
switch

NO-POWER-CORD

Table 1: HVAC/HVDC Power Cables Callout Table

Connect this end to the power supply unit.

DC Power Cable Specifications

No DC power cable is shipped with this switch.

Regulatory Standards Compliance Specifications

The following table lists the regulatory standards compliance for the switch.

Table 2: Regulatory Standards Compliance: Safety and EMC

Description

Specification

Products should comply with CE Markings according to directives 2004/108/EC
and 2006/95/EC.

Regulatory compliance

• CAN/CSA-C22.2 No. 60950-1 Second Edition

• EN 60950-1 Second Edition

• IEC 60950-1 Second Edition

• AS/NZS 60950-1

• GB4943

Safety

Cisco Nexus 9364C-GX ACI-Mode Switch Hardware Installation Guide

System Specifications

DC Power Cable Specifications

Summary of Contents for Nexus 9364C-GX

































































Search results

Summary of Contents for Nexus 9364C-GX

Reviews:

Related manuals for Nexus 9364C-GX

Brands by name

Popular brands

Cisco Nexus 9364C-GX, Hardware Installation Manual

Search results

Summary of Contents for Nexus 9364C-GX

Reviews:

Related manuals for Nexus 9364C-GX

Brands by name

Popular brands