manualshive.com logo in svg

Cisco Nexus 2000 Series, Installation Manual

Share
Download
Cisco Nexus 2000 Series Installation Manual Download Page 145

C H A P T E R

 

5-1

Cisco Nexus 2000 Series Hardware Installation Guide

 

5

Connecting a Cisco Nexus Fabric Extender

This chapter describes how to connect the ports on a Cisco Nexus Fabric Extender (FEX).

Caution

When running power and data cables in overhead or subfloor cable trays, we strongly recommend that 
you have power cables and other potential noise sources as far away as practical from network cabling 
that terminates on Cisco equipment. In situations where long parallel cable runs cannot be separated by 
at least 3.3 feet (1 m), we recommend that you shield any potential noise sources by housing them in a 
grounded metallic conduit.

This chapter includes the following sections:

•

Preparing for Network Connections, page 5-2

•

Connecting to the 1-Gigabit Ethernet Port, page 5-2

•

Connecting to a 10-Gigabit and 40-Gigabit Ethernet Port, page 5-2

Summary of Contents for Nexus 2000 Series































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands