Cisco NCS 5700 Series Hardware Installation Manual Download Page 31

Page: 31 / 120

• M4 screws to fix ground lug (2)

Accessory Kits for Fixed Port Routers

The following table contains the accessory kit PIDs and the items present in the accessory kits of the fixed
port routers. The rack mount kit present in the accessory kit contains the screws and brackets required for
installation.

Table 4: Accessory Kits Information

Items in Accessory Kit-1

Accessory Kit-1

Router

Rack mount kit and ground lug kit

8200-1RU-KIT

NCS-57B1-6D24-SYS

NCS-57B1-5DSE-SYS

Rack mount kit and ground lug kit

NC57-3RU-ACC-KIT

NCS-57C3-MOD-SE-S

NCS 57C3-MOD-S

Prepare Your Location

This section illustrates how the building that houses the chassis must be properly grounded to the earth ground.

This image is only for representational purposes. Your grounding requirement depends on your building.

Note

Hardware Installation Guide for Cisco NCS 5700 Series Fixed-Port Routers

Prepare for Installation

Accessory Kits for Fixed Port Routers

Summary of Contents for NCS 5700 Series
























































































































Search results

Summary of Contents for NCS 5700 Series

Reviews:

Brands by name

Popular brands

Cisco NCS 5700 Series, Hardware Installation Manual

Search results

Summary of Contents for NCS 5700 Series

Reviews:

Brands by name

Popular brands