manualshive.com logo in svg

Cisco NCS 5700 Series, Hardware Installation Manual

Share
Download
Cisco NCS 5700 Series Hardware Installation Manual Download Page 109

Status

Color

LED

Critical alarm - system-scope (including RP0).

Red

ALRM
(ALARM)

Major alarm - system-scope (including RP0).

Amber

No alarm.

Off

SyncE PLL is locked to an input source.

Green

SYNC

SyncE PLL not-locked to any input source.

Amber

SyncE not configured.

Off

Fans are working normally.

Green

FAN

System is operating with one fan failure.

Amber

Missing a fan or multiple fan failures.

Red

Chassis not receiving power.

Off

POWER

Chassis powered on and normal.

Green

Chassis powered off and in retry mode due to thermal or fan failure.

Amber

Chassis power failure.

Power supply failure, due to one of the following conditions:

• Over voltage

• Over current

• Over Temperature

• Fan failure

Red

GNSS is not configured.

Off

GNSS

GNSS is locked to an RF input (Satellites).

Green

GNSS Receiver not-locked RF input (Satellites).

Amber

Route Processor Card LEDs

On the NC57-MOD-RP2-E route processor card, the Status (STS), Active (ACT), and Attention (ATTN)
LEDs are located on the lower left front of the route processor card. The management port link and active
LEDs are located immediately below the port on the front of the module.

Hardware Installation Guide for Cisco NCS 5700 Series Fixed-Port Routers

103

LEDs

Route Processor Card LEDs

Summary of Contents for NCS 5700 Series

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands