Cisco NCS 5000 Series Hardware Installation Manual Download Page 57

Page: 57 / 72

Cisco NCS 5011 Router

Property

0 to 10,000 ft (0 to 3000 m)

Altitude

Power Specifications

This section describes the power specifications for the Cisco NCS 5000 Series routers.

Specifications for the Cisco NCS 5001 Power Supply

The following table lists the Power supply specifications for the Cisco NCS 5001 Series routers.

Table 17: Specifications for the Cisco NCS 5001 AC Power Supply

Specifications

AC Power Supply Properties

357 W

Typical operating power

650 W

Maximum Power

110/220

Input Voltage

47 Hz to 53 Hz

Frequency

94% (At 50% Load)

Efficiency

Yes

RoHS Compliance

Yes

Hot Swappable

Yes

Port side exhaust air flow power supply

Yes

Port side intake air flow power supply

Table 18: Specifications for the Cisco NCS 5001 DC Power Supply

Specifications

DC Power Supply Properties

511 W

Typical operating power

930 W

Maximum Power

-48/-60

Input Voltage

94% (At 50% Load)

Efficiency

Hardware Installation Guide for Cisco NCS 5000 Series Routers

Technical Specifications

Power Specifications

Summary of Contents for NCS 5000 Series









































































Search results

Summary of Contents for NCS 5000 Series

Reviews:

Cisco NCS 5000 Series, Hardware Installation Manual, Page: 57 / 72

Search results

Summary of Contents for NCS 5000 Series

Reviews: