manualshive.com logo in svg

Cisco NCS 5000 Series, Hardware Installation Manual, Page: 38 / 72

Share
Download
Cisco NCS 5000 Series Hardware Installation Manual Download Page 38

3 - Label

Step 2

Install the ground lug bracket to the mounting holes with two flat head M4 X 7mm screws.

Step 3

Install ground lug to the ground lug bracket with two pan head M4 screws.

Step 4

Using a wire-stripping tool, remove the covering from one end of the grounding cable and insert the stripped
end of the grounding cable to the open end of the grounding lug.

Step 5

Prepare the other end of the ground cable and connect it to an appropriate grounding point in your site to
ensure adequate earth ground.

Starting Cisco NCS 5000

This section provides instructions for powering up the Cisco NCS 5000 series routers and verifying their
component installation.

Do not connect the Ethernet port to the LAN until the initial router configuration has been performed.

Note

Warning

When installing or replacing the unit, the ground connection must always be made first and disconnected
last.

Note

To power up the router and verify hardware operation, follow these steps:

Procedure

Step 1

Verify that the power supply and the fan modules are installed.

Depending on the outlet receptacle on your power distribution unit, you may need the optional jumper
power cord to connect the router to your outlet receptacle. See the

Jumper Power Cord, on page 57

section.

Note

   Hardware Installation Guide for Cisco NCS 5000 Series Routers

30

Installing the NCS 5000 Router

Starting Cisco NCS 5000

Summary of Contents for NCS 5000 Series









































































Reviews:

No comments