manualshive.com logo in svg

Cisco NCS 5000 Series, Hardware Installation Manual, Page: 29 / 72

Share
Download
Cisco NCS 5000 Series Hardware Installation Manual Download Page 29

Installing Cisco NCS 5002

This section describes how to use the rack-mount kit provided with the router to install the Cisco NCS 5002
router into a cabinet or rack that meets the requirements described in

Cabinet and Rack Installation , on page

45

.

Caution

If the rack is on wheels, ensure that the brakes are engaged or that the rack is otherwise stabilized.

Note

The following table lists the items contained in the rack-mount kit provided with the Cisco NCS 5002 router.

Table 9:  Cisco NCS 5002 Router Rack-Mount Kit

Part Description

Quantity

Rack-mount brackets

4

M4 x 0.7 x 7-mm Phillips flat-head screws

16

Rack-mount guides

4

Slider rails

2

Procedure

Step 1

Install the front rack-mount brackets on the router as follows:

a) Position a front rack-mount bracket on the side of the router with its two holes aligned to two holes on the

front side of the router, and then use two M4 screws to attach the bracket to the router.

Hardware Installation Guide for Cisco NCS 5000 Series Routers    

21

Installing the NCS 5000 Router

Installing Cisco NCS 5002

Summary of Contents for NCS 5000 Series









































































Reviews:

No comments