Cisco NCS 2000 series Troubleshooting Manual Download Page 282 | Manualshive

Page: 282 / 602

background image

• Removal of an SFP from the client ports of a Y-cable protection group card causes an IMPROPRMVL

(PPM) alarm.

The working port raises the CR,IMPROPRMVL,SA alarm and the protected port raises the
MN,IMPROPRMVL,NSA alarm. The severity on the client ports is changed according to the protection
switch state.

• Electrical issues such as short circuit or failure of DC-DC conversion.

Clear the IMPROPRMVL Alarm

SUMMARY STEPS

1.

In node view (single-shelf mode) or shelf view (multishelf mode), right-click the card reporting the
IMPROPRMVL.

2.

Choose

Delete

from the shortcut menu.

3.

If any ports on the card are in service, place them out of service (OOS,MT):

4.

If a circuit has been mapped to the card, complete the

Delete a Circuit, on page 454

procedure.

5.

If the card is paired in a protection scheme, delete the protection group by completing the following steps:

6.

If the card is provisioned for DCC, delete the DCC provisioning by completing the following steps:

7.

If the card is used as a timing reference, change the timing reference by completing the following steps:

DETAILED STEPS

Step 1

In node view (single-shelf mode) or shelf view (multishelf mode), right-click the card reporting the IMPROPRMVL.

Step 2

Choose

Delete

from the shortcut menu.

CTC does not allow you to delete the reporting card if the card is in service, does have circuits mapped to it,
is paired in a working protection scheme, has DCC enabled, or is used as a timing reference.

Note

Step 3

If any ports on the card are in service, place them out of service (OOS,MT):

Before placing a port out of service (OOS,MT) or OOS,DSBLD (or Locked,disabled), ensure that no live traffic
is present.

Caution

a) In node view (single-shelf mode) or shelf view (multishelf mode), double-click the reporting card to open the card

view.

b) Click the

Provisioning

>

Line

tabs.

c) Click the Admin State column of any in-service (IS) ports.
d) Choose

OOS,MT

(or

Locked,maintenance

) to take the ports out of service.

Step 4

If a circuit has been mapped to the card, complete the

Delete a Circuit, on page 454

procedure.

Before deleting the circuit, ensure that the circuit does not carry live traffic.

Caution

Step 5

If the card is paired in a protection scheme, delete the protection group by completing the following steps:

a) Click

View

>

Go to Previous View

to return to node view (single-shelf mode) or shelf view (multishelf mode).

b) If you are already in node view (single-shelf mode) or shelf view (multishelf mode), click the

Provisioning

>

Protection

tab.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

236

Alarm Troubleshooting

Clear the IMPROPRMVL Alarm

«
...
280
281
282
283
284
...
»

Summary of Contents for NCS 2000 series



























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for NCS 2000 series

Brand: JCG Pages: 3

Brand: AMD Pages: 20

Brand: Endace Pages: 51

RS-232/422/485 Serial Card CE 3PXCC4A

Brand: B&B Electronics Pages: 47

Brand: B&B Electronics Pages: 2

Duinotech Lilypad Plus XC3920

Brand: Jaycar Electronics Pages: 2

Brand: Idis Pages: 85

PCIe/PXIe-6301 Series

Brand: JYTEK Pages: 46

Brand: Xantech Pages: 4

E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX MODULE GUIDE REV 27-9-2010

Brand: Juniper Pages: 122

Elinx EIR510 Series

Brand: B&B Electronics Pages: 2

Brand: Casablanca Pages: 13

CyberSWITCH CSX101

Brand: Cabletron Systems Pages: 72

Brand: B+B SmartWorx Pages: 50

Brand: Cradlepoint Pages: 2

Power System S914

Brand: IBM Pages: 48

Brand: ADDON Pages: 4

Extreme Spirit Il

Brand: Thermaltake Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands