Cisco N9K-C9332C Hardware Installation Manual Download Page 59

Page: 59 / 70

Power Cable Specifications

The following sections specify the power cables that you can order and use with this switch.

Power Cable Specifications for AC Power Supplies

Cord Set Description

Power Cord Part Number

Locale

Power Cord Jumper, C13-C14
Connectors, 6.6 feet (2.0 m)

CAB-C13-C14-2M

Power cord, C13 to C14 (recessed
receptacle), 10 A, 9.8 feet (3 m)

CAB-C13-C14-AC

Cabinet jumper power cord, 250
VAC, 10 A, C14-C13 connectors,
2.3 feet (0.7 m)

CAB-C13-CBN

250 V, 10 A, 8.2 feet (2.5 m)

CAB-250V-10A-AR

Argentina

250 VAC, 10 A, 3112 plug, 8.2 feet
(2.5 m)

CAB-9K10A-AU

Australia

250 V, 10 A, 6.9 feet (2.1 m)

CAB-250V-10A-BR

Brazil

250 VAC, 10 A, CEE 7/7 plug, 8.2
feet (2.5 m)

CAB-9K10A-EU

European Union

10 A, 8.2 feet (2.5 m)

CAB-IND-10A

India

250 V, 10 A, 8.2 feet (2.5 m)

CAB-250V-10A-IS

Israel

250 VAC, 10 A, CEI 23-16/VII
plug, 8.2 feet (2.5 m)

CAB-9K10A-IT

Italy

125 VAC, 13 A, NEMA 5-15 plug,
8.2 feet (2.5 m)

CAB-9K12A-NA

North America

NEMA L6-20-C13, 6.6 feet (2.0 m)

CAB-AC-L620-C13

North America

200/240V, 6A, 8.2 feet (2.5 m)

CAB-N5K6A-NA

North America

250 V, 10 A, 8.2 feet (2.5 m)

CAB-250V-10A-CN

Peoples Republic of China

250 V, 10 A, 8.2 feet (2.5 m)

CAB-250V-10A-ID

South Africa

250 VAC, 10 A, MP232 plug, 8.2
feet (2.5 m)

CAB-9K10A-SW

Switzerland

250 VAC, 10 A, BS1363 plug (13
A fuse), 8.2 (2.5 m)

CAB-9K10A-UK

United Kingdom

Cisco Nexus 9332C ACI-Mode Switch Hardware Installation Guide

System Specifications

Power Cable Specifications

Summary of Contents for N9K-C9332C







































































Search results

Summary of Contents for N9K-C9332C

Reviews:

Related manuals for N9K-C9332C

Brands by name

Popular brands

Cisco N9K-C9332C, Hardware Installation Manual

Search results

Summary of Contents for N9K-C9332C

Reviews:

Related manuals for N9K-C9332C

Brands by name

Popular brands