manualshive.com logo in svg

Cisco IP Phone 6841, Administration Manual

Share
Download
Cisco IP Phone 6841 Administration Manual Download Page 49

End of LLDPDU TLV

The value is 2-octet, all zero. This TLV is mandatory and only one is allowed for the outgoing and incoming
LLDPDUs.

Port Description TLV

For the outgoing LLDPDU, in the Port Description TLV, the value for the port description is the same as

“

Port ID TLV

”

for CDP. The incoming LLDPDU, the Port Description TLV, is ignored and not validated.

Only one Port Description TLV is allowed for outgoing and incoming LLDPDUs.

System Name TLV

For the Cisco IP Phone, the value is SEP+MAC address.

Example:

SEPAC44F211B1D0

The incoming LLDPDU, the System Name TLV, is ignored and not validated. Only one System Name TLV
is allowed for the outgoing and incoming LLDPDUs.

System Capabilities TLV

For the outgoing LLDPDU, in the System Capabilities TLV, the bit values for the 2 octet system capabilities
fields should be set for Bit 2 (Bridge) and Bit 5 (Phone) for a phone with a PC port. If the phone does not
have a PC port, only Bit 5 should be set. The same system capability value should be set for the enabled
capability field.

For the incoming LLDPDU, the System Capabilities TLV is ignored. The TLV is not validated semantically
against the MED device type.

The System Capabilities TLV is mandatory for outgoing LLDPDUs. Only one System Capabilities TLV is
allowed.

Management Address TLV

The TLV identifies an address associated with the local LLDP agent (that may be used to reach higher layer
entities) to assist discovery by network management. The TLV allows the inclusion of both the system interface
number and an object identifier (OID) that are associated with this management address, if either or both are
known.

•

TLV information string length

—

This field contains the length (in octets) of all the fields in the TLV

information string.

•

Management address string length

—

This field contains the length (in octets) of the management address

s management address fields.

System Description TLV

The TLV allows the network management to advertise the system description.

•

TLV information string length

—

This field indicates the exact length (in octets) of the system description.

Cisco IP Phone 6800 Series Multiplatform Phones Administration Guide    

35

VLAN Settings

Summary of Contents for IP Phone 6841

















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands