manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

816

Configuring IP Unicast Routing

 

Enabling IPv4 Unicast Routing

Enabling IPv4 Unicast Routing 

By default, the switch is in Layer 2 switching mode and IP routing is disabled. To use the Layer 3 capabilities of the switch, 
you must enable IP routing.

BEFORE YOU BEGIN

Review the 

Guidelines and Limitations, page 798

.

DETAILED STEPS

Use the

 no ip routing

 global configuration command to disable routing.

EXAMPLE

This example shows how to enable IP routing using RIP as the routing protocol:

Switch# 

configure terminal 

Enter configuration commands, one per line.  End with CNTL/Z.

Switch(config)# 

ip routing 

Switch(config)# 

router rip

 

Switch(config-router)# 

network 10.0.0.0 

Command

Purpose

show arp

Display the entries in the ARP table.

show hosts 

Display the default domain name, style of lookup service, name server 
hosts, and the cached list of hostnames and addresses.

show ip aliases

Display IP addresses mapped to TCP ports (aliases).

show ip arp

Display the IP ARP cache.

show ip interface

 [

interface-id

]

Display the IP status of interfaces.

show ip irdp

Display IRDP values.

show ip masks 

address

Display the masks used for network addresses and the number of 
subnets using each mask.

show ip redirects

Display the address of a default gateway.

show ip route 

[

address

 [

mask

]] | 

[

protocol

]

Display the current state of the routing table.

show ip route summary

Display the current state of the routing table in summary form.

Command

Purpose

1.

configure terminal

Enter global configuration mode.

2.

ip routing

 

Enable IP routing.

3.

router

 

ip_routing_protocol

 

Specify an IP routing protocol. This step might include other 
commands, such as specifying the networks to route with 
the 

network

 (RIP) router configuration command. For 

information on specific protocols, see sections later in this 
chapter.

4.

end

 

Return to privileged EXEC mode.

5.

show running-config

Verify your entries.

6.

copy running-config startup-config

 

(Optional) Save your entries in the configuration file.

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

N-Tron 700 Series User Manual & Installation Manual preview
700 Series
Brand: N-Tron Pages: 101
Juniper TX MATRIX PLUS Hardware Manual preview
TX MATRIX PLUS
Brand: Juniper Pages: 502
Idis DR-8432 Installation Manual preview
DR-8432
Brand: Idis Pages: 31
Patton electronics SMARTNODE 4552 Getting Started Manual preview
SMARTNODE 4552
Brand: Patton electronics Pages: 65
Funkwerk TR 200 aw/ bw Operating Instructions preview
TR 200 aw/ bw
Brand: Funkwerk Pages: 2
H3C S12500R-2L Installation Manual preview
S12500R-2L
Brand: H3C Pages: 77
AOpen 4-Port 10/100Mbps Ethernet Broadband Router User Manual preview
4-Port 10/100Mbps Ethernet Broadband Router
Brand: AOpen Pages: 41
Moxa Technologies PT-7710 Series Hardware Installation Manual preview
PT-7710 Series
Brand: Moxa Technologies Pages: 2
Perle IOLAN MDC User Manual preview
IOLAN MDC
Brand: Perle Pages: 491
MSNswitch UIS-322b Quick Installation Manual preview
UIS-322b
Brand: MSNswitch Pages: 2
XtendLan XL-IPM401 User Manual preview
XL-IPM401
Brand: XtendLan Pages: 21
Ariesys AMK Series User'S Reference Manual preview
AMK Series
Brand: Ariesys Pages: 10
H3C SecPath F1070 Manual preview
SecPath F1070
Brand: H3C Pages: 68
NetCommWireless NTC-220 Series Quick Start Manual preview
NTC-220 Series
Brand: NetCommWireless Pages: 28
Juniper MX104 Quick Start Manual preview
MX104
Brand: Juniper Pages: 30
Nortel Passport 8608GTE Specifications preview
Passport 8608GTE
Brand: Nortel Pages: 10
XtendLan XL-GRT402S User Manual preview
XL-GRT402S
Brand: XtendLan Pages: 54
Matrix Switch Corporation MSC-CP32X1E Product Manual preview
MSC-CP32X1E
Brand: Matrix Switch Corporation Pages: 48

Brands by name

Popular brands

Load more brands