manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

805

   

Configuring IP Unicast Routing

Configuring IP Addressing

DETAILED STEPS

To remove an entry from the ARP cache, use the

 no arp

 

ip-address hardware-address type

 global configuration 

command. To remove all nonstatic entries from the ARP cache, use the 

clear arp-cache 

privileged EXEC command

.

EXAMPLE

Switch# 

configure terminal 

Enter configuration commands, one per line.  End with CNTL/Z.

Switch(config)# 

arp 10.0.0.0 aabb.cc03.8200 arpa

Switch(config)# 

end

Setting ARP Encapsulation

By default, Ethernet ARP encapsulation (represented by the 

arpa

 keyword) is enabled on an IP interface. You can change 

the encapsulation methods to SNAP if required by your network. 

BEFORE YOU BEGIN

The encapsulation type specified in this procedure should match the encapsulation type specified in the 

Defining a Static 

ARP Cache, page 804

. 

Command

Purpose

1.

configure terminal

Enter global configuration mode.

2.

arp

 ip-address hardware-address

 

type

Globally associate an IP address with a MAC (hardware) 
address in the ARP cache, and specify encapsulation 
type as one of these:

arpa

—ARP encapsulation for Ethernet interfaces

snap

—Subnetwork Address Protocol encapsulation 

for Token Ring and FDDI interfaces

sap

—HP’s ARP type

3.

arp

 ip-address hardware-address type 

[

alias

]

(Optional) Specify that the switch respond to ARP 
requests as if it were the owner of the specified IP 
address.

4.

interface

 

interface-id

Enter interface configuration mode, and specify the 
interface to configure.

5.

no shutdown

 

Enable the interface if necessary. By default, UNIs and 
ENIs are disabled and NNIs are enabled. 

6.

arp timeout

 

seconds

(Optional) Set the length of time an ARP cache entry will 
stay in the cache. The default is 14400 seconds (4 
hours). The range is 0 to 2147483 seconds.

7.

end

 

Return to privileged EXEC mode.

8.

show interfaces 

[

interface-id

]

Verify the type of ARP and the timeout value used on all 
interfaces or a specific interface.

9.

show arp

or

show ip arp

View the contents of the ARP cache.

10.

copy running-config startup-config 

(Optional) Save your entries in the configuration file.

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

IBM 3708 Description preview
3708
Brand: IBM Pages: 342
H3C SR6600 SPE-FWM Vxlan Command Reference preview
SR6600 SPE-FWM
Brand: H3C Pages: 45
H3C SR6600 SPE-FWM Manual preview
SR6600 SPE-FWM
Brand: H3C Pages: 80
H3C MSR 5600 Configuration Manual preview
MSR 5600
Brand: H3C Pages: 46
H3C MSR 5600 Comware 7 Vxlan Command Reference preview
MSR 5600
Brand: H3C Pages: 45
H3C MSR 3600 Quick Start preview
MSR 3600
Brand: H3C Pages: 4
H3C SR6600 SPE-FWM Fundamentals Configuration Manual preview
SR6600 SPE-FWM
Brand: H3C Pages: 184
Belkin F5D9001 Series Manual preview
F5D9001 Series
Brand: Belkin Pages: 72
Helmholz REX 200 Quick Start Manual preview
REX 200
Brand: Helmholz Pages: 28
Delta Electronics DTE-20T Instruction Sheet preview
DTE-20T
Brand: Delta Electronics Pages: 1
TRENDnet TW-100 Specifications preview
TW-100
Brand: TRENDnet Pages: 2
Weidmuller IE-SW-VL16-14TX-2SC Hardware Installation Manual preview
IE-SW-VL16-14TX-2SC
Brand: Weidmuller Pages: 17
XNET INS2000 Install Manual preview
INS2000
Brand: XNET Pages: 17
Tandberg Data SUPERLOADER DLT MAGAZINE Quick Start Manual preview
SUPERLOADER DLT MAGAZINE
Brand: Tandberg Data Pages: 6
C&H Active Module Carrier VX402C-64 User Manual preview
Active Module Carrier VX402C-64
Brand: C&H Pages: 32
XYZ Machine Tools TRAK 2OP M11 Mill Safety, Installation, Maintenance, Service And Parts List preview
TRAK 2OP M11 Mill
Brand: XYZ Machine Tools Pages: 203
Thecus N12000 series User Manual preview
N12000 series
Brand: Thecus Pages: 120
ANEP P4GU VoLTE Technical Data Sheet preview
P4GU VoLTE
Brand: ANEP Pages: 48

Brands by name

Popular brands

Load more brands