manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

503

Cisco Systems, Inc.

www.cisco.com

 

Configuring UDLD

Prerequisites for UDLD

When configuring the mode (normal or aggressive), make sure that the same mode is configured on both sides of 
the link.

Restrictions for UDLD

UDLD is not supported on ATM ports. 

A UDLD-capable port cannot detect a unidirectional link if it is connected to a UDLD-incapable port of another 
switch.

Loop guard works only on point-to-point links. We recommend that each end of the link has a directly connected 
device that is running STP.

Information About UDLD

UDLD

UniDirectional Link Detection (UDLD) is a Layer 2 protocol that enables devices connected through fiber-optic or 
twisted-pair Ethernet cables to monitor the physical configuration of the cables and detect when a unidirectional link 
exists. All connected devices must support UDLD for the protocol to successfully identify and disable unidirectional links. 
When UDLD detects a unidirectional link, it disables the affected port and alerts you. Unidirectional links can cause a 
variety of problems, including spanning-tree topology loops. 

Modes of Operation

UDLD supports two modes of operation: normal (the default) and aggressive. In normal mode, UDLD can detect 
unidirectional links due to misconnected ports on fiber-optic connections. In aggressive mode, UDLD can also detect 
unidirectional links due to one-way traffic on fiber-optic and twisted-pair links and to misconnected ports on fiber-optic 
links. 

In normal and aggressive modes, UDLD works with the Layer 1 mechanisms to learn the physical status of a link. At Layer 
1, autonegotiation takes care of physical signaling and fault detection. UDLD performs tasks that autonegotiation cannot 
perform, such as detecting the identities of neighbors and shutting down misconnected ports. When you enable both 
autonegotiation and UDLD, the Layer 1 and Layer 2 detections work together to prevent physical and logical unidirectional 
connections and the malfunctioning of other protocols.

A unidirectional link occurs whenever traffic sent by a local device is received by its neighbor but traffic from the neighbor 
is not received by the local device. 

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

Parkside POF 1200 A1 Operation Manual preview
POF 1200 A1
Brand: Parkside Pages: 55
Parkside POF 1200 A1 Operation And Safety Notes preview
POF 1200 A1
Brand: Parkside Pages: 34
Dahua NVR2104-S2 Quick Start Manual preview
NVR2104-S2
Brand: Dahua Pages: 6
Banner Sure Cross DX70 Instruction Manual preview
Sure Cross DX70
Brand: Banner Pages: 35
National Instruments NI WLS/ENET-9163 User Manual preview
NI WLS/ENET-9163
Brand: National Instruments Pages: 36
Teletronics International TT 900 User Manual preview
TT 900
Brand: Teletronics International Pages: 57
ICP DAS USA iWSN-200E Quick Start Manual preview
iWSN-200E
Brand: ICP DAS USA Pages: 8
AirLive Ether-GSH24T v3 Quick Setup Manual preview
Ether-GSH24T v3
Brand: AirLive Pages: 2
Raven RFMOW V2 User Manual preview
RFMOW V2
Brand: Raven Pages: 33
Idis DR-2308P Quick Manual preview
DR-2308P
Brand: Idis Pages: 18
Thecus N2520 series User Manual preview
N2520 series
Brand: Thecus Pages: 130
Tenda FH456 User Manual preview
FH456
Brand: Tenda Pages: 82
Cabletron Systems TRXMIM-24A User Manual preview
TRXMIM-24A
Brand: Cabletron Systems Pages: 56
Lanpro LP-SW811 User Manual preview
LP-SW811
Brand: Lanpro Pages: 6
IEI Technology PUZZLE-5030 User Manual preview
PUZZLE-5030
Brand: IEI Technology Pages: 119
GarrettCom DynaStar DS2000-IFR Installation And Maintenance Manual preview
DynaStar DS2000-IFR
Brand: GarrettCom Pages: 40
VAMISOUND Schoeps electret Building Instructions preview
Schoeps electret
Brand: VAMISOUND Pages: 15
Crestron UC-CAM-UPGRD-300 Quick Start preview
UC-CAM-UPGRD-300
Brand: Crestron Pages: 2

Brands by name

Popular brands

Load more brands