manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

288

Configuring VLANs

 

How to Configure VLANs

Load Sharing Using STP Port Priorities

Configuring Load Sharing Using STP Path Cost

Command

Purpose

1.

configure terminal

Enters global configuration mode on Switch A.

2.

vtp domain

 

domain-name

Configures a VTP administrative domain.

The domain name can be 1 to 32 characters.

3.

vtp mode server

Configures Switch A as the VTP server.

4.

end

Returns to privileged EXEC mode.

5.

show vtp status

Verifies the VTP configuration on both Switch A and Switch B.

6.

show vlan

Verifies that the VLANs exist in the database on Switch A.

7.

configure terminal

Enters global configuration mode.

8.

interface 

interface-id_1

 

Defines the interface to be configured as a trunk, and enters interface 
configuration mode.

9.

switchport mode trunk

Configures the port as a trunk port.

10.

end

Returns to privileged EXEC mode.

11.

show interfaces 

interface-id_1

 switchport

Verifes the VLAN configuration.

12.

Repeat Steps 7 through 10 on Switch A for 
a second port in the switch.

13.

Repeat Steps 7 through 10 on Switch B to 
configure the trunk ports that connect to the 
trunk ports configured on Switch A.

14.

show vlan

When the trunk links come up, VTP passes the VTP and VLAN 
information to Switch B. Verifies that Switch B has learned the VLAN 
configuration.

15.

configure terminal

Enters global configuration mode on Switch A.

16.

interface 

interface-id_1 

Defines the interface to set the STP port priority, and enters interface 
configuration mode.

17.

spanning-tree vlan 8-10 port-priority 16

Assigns the port priority of 16 for VLANs 8 through 10.

18.

exit

Returns to global configuration mode.

19.

interface 

interface-id_2

Defines the interface to set the STP port priority, and enters interface 
configuration mode.

20.

spanning-tree vlan 3-6 port-priority 16

Assigns the port priority of 16 for VLANs 3 through 6.

21.

end

Returns to privileged EXEC mode.

Command

Purpose

1.

configure terminal

Enters global configuration mode on Switch A.

2.

interface 

interface-id_1

Defines the interface to be configured as a trunk, and enters interface 
configuration mode.

3.

switchport mode trunk

Configures the port as a trunk port. 

4.

exit

Returns to global configuration mode.

5.

Repeat Steps 2 through 4 on a second interface in Switch A.

6.

end

Returns to privileged EXEC mode.

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

H3C SR6600 SPE-FWM Vxlan Command Reference preview
SR6600 SPE-FWM
Brand: H3C Pages: 45
H3C SR6600 SPE-FWM Manual preview
SR6600 SPE-FWM
Brand: H3C Pages: 80
H3C MSR 5600 Configuration Manual preview
MSR 5600
Brand: H3C Pages: 46
H3C MSR 5600 Comware 7 Vxlan Command Reference preview
MSR 5600
Brand: H3C Pages: 45
H3C MSR 3600 Quick Start preview
MSR 3600
Brand: H3C Pages: 4
H3C SR6600 SPE-FWM Fundamentals Configuration Manual preview
SR6600 SPE-FWM
Brand: H3C Pages: 184
Patton electronics 4520 Specification Sheet preview
4520
Brand: Patton electronics Pages: 2
Patton electronics 4520 Getting Started Manual preview
4520
Brand: Patton electronics Pages: 86
Zonet ZEW1505 Quick Installation Manual preview
ZEW1505
Brand: Zonet Pages: 10
Samsung NAS Series Hardware User Manual preview
NAS Series
Brand: Samsung Pages: 65
QNO 2WAN 3LAN User Manual preview
2WAN 3LAN
Brand: QNO Pages: 106
Face XR18 User Manual preview
XR18
Brand: Face Pages: 8
XNET INS2000 Install Manual preview
INS2000
Brand: XNET Pages: 17
C&H Active Module Carrier VX402C-64 User Manual preview
Active Module Carrier VX402C-64
Brand: C&H Pages: 32
Caen A 1735 Technical Information Manual preview
A 1735
Brand: Caen Pages: 14
G&D DL-DVI-Vision-IP Series Installation And Operation Manual preview
DL-DVI-Vision-IP Series
Brand: G&D Pages: 228
Comet Labs GS8+ User Manual preview
GS8+
Brand: Comet Labs Pages: 11
ADTRAN NetVanta Serial Dial Backup Interface Module (DIM) none Quick Start Manual preview
NetVanta Serial Dial Backup Interface Module (DIM) none
Brand: ADTRAN Pages: 2

Brands by name

Popular brands

Load more brands