manualshive.com logo in svg

Cisco CRS Series, Installation Manual, Page: 37 / 54

Share
Download
Cisco CRS Series Installation Manual Download Page 37

Installing the Exhaust Air Deflector

This section describes how to install the exhaust air deflector on the rear of the Cisco CRS Series Enhanced
16-slot Line Card Chassis. For complete information on regulatory compliance and safety, see

Regulatory

Compliance and Safety Information for the Cisco CRS Carrier Routing System

.

Prerequisites

Before performing this task, perform the following procedures:

Required Tools and Equipment

You need the following tools and equipment to perform this task:

•

6-in. long number 2 Phillips screwdriver

•

Rear exhaust air deflector (set aside earlier)

Steps

To install the exhaust air deflector on the chassis, perform the following steps:

SUMMARY STEPS

1.

Locate the mounting position standoffs on each side of the exhaust opening.

2.

Position the lower cutouts on the bottom of the air deflector with the lower standoffs.

3.

Rotate the air deflector forward until it is seated on the upper standoff.

4.

Tighten the captive screw on both sides.

Cisco CRS Routers 16-Slot Line Card Chassis Enhanced Router Installation Guide    

37

Installing Power Components

Installing the Exhaust Air Deflector

Summary of Contents for CRS Series























































Reviews:

No comments