manualshive.com logo in svg

Cisco Catalyst 9400 Series, Hardware Installation Manual

Share
Download
Cisco Catalyst 9400 Series Hardware Installation Manual Download Page 96

Installing a Fan Tray from the Front

To install a fan tray from the front, follow the steps described here.

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement

1030

Warning

No user-serviceable parts inside. Do not open.

Statement 1073

Warning

Installation of the equipment must comply with local and national electrical codes.

Statement 1074

Warning

Before you begin

Ensure that a replacement fan tray (with the adapter module detatched), is ready for installation. There is a
time constraint when you remove and replace a fan tray in a system that is powered on - if you have enabled
the service mode prior to servicing, fan-less operation can be safely assured for four minutes only.

You may need a Phillips-head screwdriver to loosen the captive installation screws.

Procedure

Step 1

Grasp the front handle with one hand and place your other hand underneath the fan tray to support it. Hold
the fan tray with the fans facing to the right.

Step 2

Place the fan tray in the fan tray bay such that it rests on the chassis, and then lift the fan tray up slightly,
aligning the top and bottom guides.

Cisco Catalyst 9400 Series Switches Hardware Installation Guide

90

Removing and Replacing FRUs

Installing a Fan Tray from the Front

Summary of Contents for Catalyst 9400 Series

































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands