Cisco Catalyst 9400 Series Hardware Installation Manual Download Page 133

Page: 133 / 192

Figure 35: Installing a Power Supply Blank Cover

Figure 36: Power Supply Blank Cover Installed

Power supply blank covers can be placed in any slot when fewer than eight power supplies are installed in a
chassis.

Note

Verifying the Power Supply Module Installation

Procedure

Step 1

Verify the power supply operation by checking the power supply’s front-panel LEDs. You should see the
following:

• The INPUT LED is green.

• The OUTPUT LED is green if it is an active module and blinking green if it is a redundant module.

• The FAIL LED is off.

Cisco Catalyst 9400 Series Switches Hardware Installation Guide

127

Removing and Replacing FRUs

Verifying the Power Supply Module Installation

Summary of Contents for Catalyst 9400 Series

































































































































































































Search results

Summary of Contents for Catalyst 9400 Series

Reviews:

Brands by name

Popular brands

Cisco Catalyst 9400 Series, Hardware Installation Manual

Search results

Summary of Contents for Catalyst 9400 Series

Reviews:

Brands by name

Popular brands