manualshive.com logo in svg

Cisco Catalyst 2928, Software Configuration Manual

The Cisco Catalyst 2928 is a highly reliable network switch designed to deliver unparalleled performance. With advanced features and seamless connectivity, it empowers organizations with efficient network operations. To maximize its potential, users can easily download the comprehensive Software Configuration Manual for free from our website, manualshive.com.

Share
Download
background image

 

13-6

Catalyst 2928 Switch Software Configuration Guide

OL-23389-01

Chapter 13      Configuring VLANs

Configuring Normal-Range VLANs

•

The switch supports 64 spanning-tree instances. If a switch has more active VLANs than supported 
spanning-tree instances, spanning tree can be enabled on 128 VLANs and is disabled on the 
remaining VLANs. If you have already used all available spanning-tree instances on a switch, 
adding another VLAN anywhere in the VTP domain creates a VLAN on that switch that is not 
running spanning-tree. If you have the default allowed list on the trunk ports of that switch (which 
is to allow all VLANs), the new VLAN is carried on all trunk ports. Depending on the topology of 
the network, this could create a loop in the new VLAN that would not be broken, particularly if there 
are several adjacent switches that all have run out of spanning-tree instances. You can prevent this 
possibility by setting allowed lists on the trunk ports of switches that have used up their allocation 
of spanning-tree instances.

If the number of VLANs on the switch exceeds the number of supported spanning-tree instances, 
we recommend that you configure the IEEE 802.1s Multiple STP (MSTP) on your switch to map 
multiple VLANs to a single spanning-tree instance. For more information about MSTP, see 

Chapter 17, “Configuring MSTP.”

•

To access VLAN configuration mode, enter the 

vlan 

global configuration command with a VLAN 

ID. Enter a new VLAN ID to create a VLAN, or enter an existing VLAN ID to modify that VLAN. 
You can use the default VLAN configuration (

Table 13-2

) or enter multiple commands to configure 

the VLAN. For more information about commands available in this mode, see the 

vlan 

global 

configuration command description in the command reference

 

for this release. When you have 

finished the configuration, you must exit VLAN configuration mode for the configuration to take 
effect. To display the VLAN configuration, enter the 

show vlan

 privileged EXEC command.

Saving VLAN Configuration

The configurations of VLAN IDs 1 to 1005 are always saved in the VLAN database (vlan.dat file). If the 
VTP mode is transparent, they are also saved in the switch running configuration file. You can enter the 

copy running-config startup-config 

privileged EXEC command to save the configuration in the startup 

configuration file. To display the VLAN configuration, enter the 

show vlan

 privileged EXEC command.

When you save VLAN and VTP information (including extended-range VLAN configuration 
information) in the startup configuration file and reboot the switch, the switch configuration is selected 
as follows:

•

If the VTP mode is transparent in the startup configuration, and the VLAN database and the VTP 
domain name from the VLAN database matches that in the startup configuration file, the VLAN 
database is ignored (cleared), and the VTP and VLAN configurations in the startup configuration 
file are used. The VLAN database revision number remains unchanged in the VLAN database. 

•

If the VTP mode or domain name in the startup configuration does not match the VLAN database, 
the domain name and VTP mode and configuration for the first 1005 VLANs use the VLAN 
database information. 

•

If VTP mode is server, the domain name and VLAN configuration for the first 1005 VLANs use the 
VLAN database information 

Caution

If the VLAN database configuration is used at startup and the startup configuration file contains 
extended-range VLAN configuration, this information is lost when the system boots up. 

Default Ethernet VLAN Configuration

Table 13-2

 shows the default configuration for Ethernet VLANs.

Summary of Contents for Catalyst 2928





























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Catalyst 2928

WAGO 852-1417 Operating And Assembly Instructions preview
852-1417
Brand: WAGO Pages: 2
Ubiquiti U5-24-500W Quick Start Manual preview
U5-24-500W
Brand: Ubiquiti Pages: 23
NetBurner MOD5272 Quick Start Manual preview
MOD5272
Brand: NetBurner Pages: 15
MicroNet BroadLink SP3353 Installation Manual preview
BroadLink SP3353
Brand: MicroNet Pages: 66
Enterasys X-Pedition 2000 Getting Started Manual preview
X-Pedition 2000
Brand: Enterasys Pages: 86
Novus NVIP- NVRA0104/GO User Manual preview
NVIP- NVRA0104/GO
Brand: Novus Pages: 44
Parker PCH1 T P Series User Manual preview
PCH1 T P Series
Brand: Parker Pages: 107
IBASE Technology FWA8207 Series User Manual preview
FWA8207 Series
Brand: IBASE Technology Pages: 39
HGST Ultrastar Serv24 S2122-N24-4 Installation Manual preview
Ultrastar Serv24 S2122-N24-4
Brand: HGST Pages: 36
XtendLan XL-HCW224C User Manual preview
XL-HCW224C
Brand: XtendLan Pages: 52
CalAmp Viper 100 User Manual preview
Viper 100
Brand: CalAmp Pages: 115
Rasilient ApplianceStor 15MT User Manual preview
ApplianceStor 15MT
Brand: Rasilient Pages: 30
NETGEAR ReadyNAS 3220 Series Datasheet preview
ReadyNAS 3220 Series
Brand: NETGEAR Pages: 4
Idis DR-2308P Quick Manual preview
DR-2308P
Brand: Idis Pages: 18
Abocom SDW11B Specification Sheet preview
SDW11B
Brand: Abocom Pages: 1
Tenda FH456 User Manual preview
FH456
Brand: Tenda Pages: 82
Riverbed SteelCentral NetExpress 470 Upgrade And Maintenance Manual preview
SteelCentral NetExpress 470
Brand: Riverbed Pages: 140
Cayman Systems 2E-H-W User Manual preview
2E-H-W
Brand: Cayman Systems Pages: 170

Brands by name

Popular brands

Load more brands