manualshive.com logo in svg

Cisco CableCARD, Staging Manual, Page: 29 / 184

Share
Download
Cisco CableCARD Staging Manual Download Page 29

 

 

Install Software 

734375 Rev H 

19 

 

Install Software 

Install the Application Platform Release 

The next task that you must complete before you can stage DHCTs or CableCARD 
modules is to install the current application platform software onto the DNCS.  

Application platform software consists of the OS and ResApp software. The device 
must have both of these components to function properly.  

When the software is installed on the DNCS, the staging process then delivers the 
software to the devices. Refer to 

Downloading New Client Application Platform Software 

Installation Instructions.

 

 

Install the Current Resource File 

If you are using the CVT download method to load the application platform 
software onto devices, you need to make sure that you are using the most current 
resource file (

settop.res

). This resource file contains information used by the CVT 

configuration interface on the DNCS to validate the software for both DHCTs and 
CableCARD modules to prevent loading the wrong software onto a device. 

Refer to 

Downloading New Client Application Platform Installation Instructions

 (part 

number 4003052) for more information about acquiring and installing the most 
current resource files. 

 

Install the OS Check Table (OSM Only) 

If you are using the OSM download method to stage DHCTs, you must install the 
OS check table.  

Refer to 

Downloading New Client Application Platform Software Installation Instructions

 

for more information. 

 

Summary of Contents for CableCARD

























































































































































































Reviews:

No comments