manualshive.com logo in svg

Cisco CableCARD, Staging Manual

Share
Download
Cisco CableCARD Staging Manual Download Page 21

 

 

Verify DNCS System Configuration Settings 

734375 Rev H 

11 

 

Verify DNCS System Configuration Settings 

We recommend that you 

do not change

 the default DHCT and network signaling 

parameters in the DSM-CC portion of the DNCS System Configuration window 
when you stage DHCTs. 

Note:

 For more information on the DNCS System Configuration window and the 

recommended parameter settings for that window, refer to the 

Digital Network 

Control System Online Help

 for your system release. 

 

Verify Current DNCS System Configuration Settings (DAVIC Systems) 

Verifying Current DNCS System Configuration Settings (DAVIC) 

Follow these steps to verify your current DNCS system configuration settings. 

1

 

From the Administrative Console on the DNCS, select 

System Provisioning

. 

2

 

In the System Management area of the DNCS Administrative Console, select 

DHCT Mgr

. The DHCT Manager window opens with the DHCT Manager 

Modes tab in the forefront. 

3

 

Is DHCT Registration set to 

Administrative Gateway

? 

 

If 

yes

, go to step 4. 

 

If 

no

, change the DHCT Registration setting to 

Administrative Gateway

, 

then go to step 5. 

4

 

Is IP Address Assignment set to 

Override

? 

 

If 

yes

, go to step 5. 

 

If 

no

, change the IP Address Assignment setting to 

Override

, then to go step 

5. 

5

 

Click 

Save

. The system saves your settings and the DHCT Manager window 

closes. 

6

 

Go to 

Billing System Preparation

 (on page 20). 

 

Verify Current DNCS System Configuration Settings (DOCSIS Systems) 

If your system uses DOCSIS, refer to 

DOCSIS in a DBDS Environment 

(part number 

4000358) to verify your DNCS system configuration. 

 

Summary of Contents for CableCARD

























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands