Cisco CableCARD Staging Manual Download Page 166

Page: 166 / 184

Appendix D

Adding an HDD Test Server to the BFS

156

734375 Rev H

Placing the HDD Performance Specification File on
the HDD Test Server

Note:

This procedure can be used for systems that support multiple or single sites.

In the Broadcast File Server List window, double-click the

hddtest

server. The

hddtest server opens to show its contents.

Click

File > New File

. The Set Up File window opens.

Follow these instructions to enter data into the fields of the Set Up File window:



Click in the File Name field and type

testparam.cfg



Click the Source Name arrow and select

Out of Band



Click in the File Path field and type

/dvs/resapp/Tools/testparam.cfg

Result:

The Set Up File window is configured as shown in the following

example.

Click

Save

to save your changes and close the Set Up File window. The HDD

Performance Specification file is placed on the HDD Test server. As a result, the
testparam.cfg file appears beneath the open hddtest server.

Click

File > Close

to close the Broadcast File Serve List window. You have

successfully set up the BFS to support the HDD Test.

Summary of Contents for CableCARD

























































































































































































Search results

Summary of Contents for CableCARD

Reviews:

Related manuals for CableCARD

Brands by name

Popular brands

Cisco CableCARD, Staging Manual

Search results

Summary of Contents for CableCARD

Reviews:

Related manuals for CableCARD

Brands by name

Popular brands