Cisco CableCARD Staging Manual Download Page 148 | Manualshive

Page: 148 / 184

background image

Appendix C

Setting Up Multiple Bootloader Carousels

138

734375 Rev H

Determining Available Bandwidth for BFS BIG Systems

This section provides procedures for operators with a BFS BIG to use in determining
how much bandwidth is available for inband sources. To determine the amount of
bandwidth available for additional bootloader carousels, perform the following
calculation:

Total Available Bandwidth - Bandwidth in Use = Available Bandwidth

Notes:



The inband data rate for a 64-QAM is 25 Mbps.



The inband data rate for a 256-QAM is 36 Mbps.

1

Open an xterm window on the DNCS.

2

Type one of the following, based on the system release you have installed:



For SR 4.2.1 and earlier, type

cd /export/home/dncs/doctor

and press

Enter

.



For SR 4.3 and later, type

cd /dvs/dncs/Utilities/doctor

and press

Enter

.

Note:

Be sure to type a space between

cd

and

/

.

Result:

The current directory is now the doctor directory.

3

Type

doctor -bv

and press

Enter

. A table appears and lists the inband and out-of-

band data rates on the BFS carousel. The total inband carousel bandwidth in use
is displayed in the

Aggregate IB Carousel Datarate

field.

4

Add

1 Mbps

to the data rate in the

Aggregate IB Carousel Datarate

field to

account for any overhead.

Example:

If you have a total inband data rate of 14 Mbps, add 1 Mbps for a total

of 15 Mbps in use.

14 + 1 = 15

5

Subtract the total inband carousel bandwidth in use from the total available
bandwidth to determine the unused inband bandwidth on the BFS.

Examples:



64-QAM:

From the examples above, the available bandwidth is 10 Mbps.

25 - 15 = 10 Mbps



256-QAM:

From the examples above, the available bandwidth is 21 Mbps.

36 - 15 = 21 Mbps

6

Compare the amount of unused bandwidth to the amount of bandwidth
required for the additional bootloader carousels.

«
...
146
147
148
149
150
...
»

Summary of Contents for CableCARD

























































































































































































Reviews:

No comments

Related manuals for CableCARD

iPort PT1000-CL

Brand: Pleora Technologies Pages: 29

Brand: Potek Pages: 18

Brand: Future Illuminations Pages: 2

Brand: Magtek Pages: 54

Brand: hc-cargo Pages: 38

Varispeed CIMR-G7A

Brand: YASKAWA Pages: 459

Brand: Xantech Pages: 2

Mega 100 Classic

Brand: Ellumiglow Pages: 4

Brand: Votek Pages: 33

Brand: Meicheng Pages: 6

Brand: StarTech.com Pages: 12

Brand: Digitus Pages: 3

Brand: Samlexpower Pages: 3

Brand: Kipor Pages: 18

Brand: Sungrow Pages: 112

Evershine TLC4000

Brand: Zeversolar Pages: 74

MobilePower PRO

Brand: Heyner Pages: 4

Brand: Quickfilter Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands