Cisco CableCARD Staging Manual Download Page 147 | Manualshive

Page: 147 / 184

background image

Determine Available Bandwidth for Multiple Bootloaders

734375 Rev H

137

Determining Available Bandwidth for Direct ASI Systems

This section provides procedures for operators with direct ASI to use in determining
how much bandwidth is available for inband sources. To determine the amount of
bandwidth available for additional bootloader carousels, perform the following
calculation:

Total Available Bandwidth - Bandwidth in Use = Available Bandwidth

Notes:



The inband data rate for a 64-QAM is 26 Mbps.



The inband data rate for a 256-QAM is 37 Mbps.

These rates are due to modulation coding and error corrections (real rates are
higher).

1

Open an xterm window on the DNCS.

2

Type one of the following, based on the system release you have installed:



For SR 4.2.1 and earlier, type

cd /export/home/dncs/doctor

and press

Enter

.



For SR 4.3 and later, type

cd /dvs/dncs/Utilities/doctor

and press

Enter

.

Note:

Be sure to type a space between

cd

and

/

.

Result:

The current directory is now the doctor directory.

3

Type

doctor -bv

and press

Enter

. A table appears that lists the inband and out-

of-band data rates on the BFS carousel. The total inband carousel bandwidth in
use is displayed in the

Aggregate IB Carousel Datarate

field.

4

Subtract the total inband carousel bandwidth in use from the total available
bandwidth to determine the unused inband bandwidth on the BFS.

Examples:



64-QAM:

If your total inband carousel bandwidth in use is 14 Mbps, the

available bandwidth is 12 Mbps.

26 - 14 = 12 Mbps



256-QAM:

If your total inband carousel bandwidth in use is 14 Mbps, the

available bandwidth is 23 Mbps.

37 - 14 = 23 Mbps

5

Compare the amount of unused bandwidth to the amount of bandwidth
required for the additional bootloader carousels.

6

Is there enough bandwidth to add the new bootloader carousels? (Bootloader
carousels require data rates between 1.00 and 3.00 Mbps.)



If

yes

, go to

Adding a Bootloader Source to the DNCS

(on page 142).



If

no

, refer to

Recommendations for Data Carousel Rate Management Technical

Bulletin

(part number 716377) for details on how to increase the bandwidth of

your system.

«
...
145
146
147
148
149
...
»

Summary of Contents for CableCARD

























































































































































































Reviews:

No comments

Related manuals for CableCARD

Brand: Cosel Pages: 62

Giga-McBasic-II

Brand: B&B Electronics Pages: 14

Brand: VigilLink Pages: 6

Brand: World Friendship Pages: 17

BLANKOM SDE-1265

Brand: Irenis Pages: 22

Brand: National Communications Pages: 20

Brand: AXIOMTEK Pages: 2

Brand: R3Di Pages: 10

Brand: Sunforce Pages: 1

Brand: Lika Pages: 104

climatronic converter WMS UP

Brand: WAREMA Pages: 4

Brand: IAdea Pages: 33

ColourTran-350 CTR-30-025-T-DD

Brand: Mode Lighting Pages: 2

Brand: Mobotix Pages: 44

Brand: Peak Pages: 37

Brand: Enercell Pages: 12

SM-Universal Encoder Plus

Brand: Control Techniques Pages: 112

Brand: Kiloview Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands